CENTURION SYSTEMS SECTOR II страница 6 Скачать руководство пользователя

Страница: 6 / 84

page 6

www.centsys.com

•

Safety devices must be fitted to the installation to guard against mechanical

movement risks, such as crushing, dragging and shearing

•

It is recommended that at least one warning indicator light be fitted to every system

•

Always fit the warning signs visibly to the inside and outside of the barrier

• The installer must explain and demonstrate the manual operation of the barrier in

case of an emergency, and must hand over the user guide to the user

• Explain these safety instructions to all persons authorised to use this barrier, and be

sure that they understand the hazards associated with traffic barriers

• Do not leave packing materials (plastic, polystyrene, etc.) within reach of children as

such materials are potential sources of danger

• Dispose of all waste products like packing materials, worn-out batteries, etc.

according to local regulations

• Always check the obstruction detection system and safety devices for correct

operation

• Neither Centurion Systems (Pty) Ltd, nor its subsidiaries, accepts any liability caused

by improper use of the product, or for use other than that for which the automated

system was intended

• This product was designed and built strictly for the use indicated in this

documentation. Any other use, not expressly indicated here, could compromise the

service life/operation of the product and/or be a source of danger

•

Anything that has not been specified in these instructions may be considered a risk

to your safety, and the safety of others. If you are unsure of an installation matter,

please contact your nearest distributor

SAFETY INSTRUCTIONS

Содержание SECTOR II





















































































Результаты поиска

Содержание SECTOR II

Отзывы:

Похожие инструкции для SECTOR II

Бренды по названию

Популярные бренды

CENTURION SYSTEMS SECTOR II, Руководство по установке

Результаты поиска

Содержание SECTOR II

Отзывы:

Похожие инструкции для SECTOR II

Бренды по названию

Популярные бренды