CENTURION SYSTEMS SECTOR II Скачать руководство пользователя

Страница: 5 / 84

page 5

www.centsys.com

ATTENTION

To ensure the safety of people and possessions, it is important that you

read all the following instructions.

Incorrect installation or incorrect use of the product may cause

serious harm to people and / or property.

The installer, being either professional or DIY, is the last person

on the site who can ensure that the operator is safely installed, and that

the whole system can be operated safely.

IMPORTANT

SAFETY INSTRUCTIONS

Warnings for the installer

CAREFULLY READ AND FOLLOW ALL INSTRUCTIONS before beginning to install

the product.

• All installation, repair, and service work to this product must be carried out by a

suitably qualified person

• Do not activate your barrier unless you can see it and can determine that its area of

travel is clear of people, pets, or other obstructions

• NO ONE MAY CROSS THE PATH OF A MOVING BARRIER.

Always keep people

and objects away from the barrier and its area of travel

• NEVER LET CHILDREN OPERATE OR PLAY WITH THE BARRIER CONTROLS

• Secure all easily-accessed barrier controls in order to prevent unauthorised use of the

barrier

• Do not in any way modify the components of the automated system
•

Do not install the equipment in an explosive atmosphere: the presence of flammable

gasses or fumes is a serious danger to safety

•

Before attempting any work on the system, cut electrical power to the operator and

disconnect the batteries

•

The mains power supply of the automated system must be fitted with an all-pole

switch with contact opening distance of 3mm or greater. Use of a 5A thermal breaker

with all-pole circuit break is recommended

•

Make sure that an earth leakage circuit breaker with a threshold of 30mA is fitted

upstream of the system

• Never short-circuit the battery and do not try to recharge the batteries with power

supply units other than that supplied with the product, or manufactured by

Centurion Systems (Pty) Ltd

• Make sure that the earthing system is correctly constructed, and that all metal parts

of the system are suitably earthed

SAFETY INSTRUCTIONS

Содержание SECTOR II





















































































Результаты поиска

Содержание SECTOR II

Отзывы:

Похожие инструкции для SECTOR II

Бренды по названию

Популярные бренды

CENTURION SYSTEMS SECTOR II, Руководство по установке

Результаты поиска

Содержание SECTOR II

Отзывы:

Похожие инструкции для SECTOR II

Бренды по названию

Популярные бренды