Here, X= 0 for Day Mode and 1 for Night mode.
J = 1 to 8 (Junction Line no)
NN = Last 2 digits of the Extension No.
This programming can be repeated for one Junction Line and up to 16 Extensions.
One Junction line can be programmed to land on up to 16 Extensions.
Dial #
0000 + 3X J # (To disable Ring Assignment of one Junction)
Dial #
0000 + 3X J NN 1 # (To disable Ring Assignment of one Junction & Extension)
Default
:
All the Junction Lines land on Extension number 601 and 602 in Simultaneous Mode.
Round Robin Ring
In this mode, the incoming call lands on one extension. If that extension is busy or doesn’t respond within few rings then the call shifts to another
extension.
Programming
:
#
0000 + 3X J # This program
disables the default ring assignment
.
#
0000 + 3 X J NN 0 # Here, X= 0 for Day Mode and 1 for Night mode.
J = 1 to 4 (Junction Line no)
NN = Last 2 digits of the 1
st
Round Robin Extension No.
(Not the Flexible Number)
Also note that the first Extension in Round Robin can be 601 to 616 only.
Cannot program Extension 617 to 632 in case of 432S.
# 27 NN XXX Where, XXX= 2
nd
Extension number of Round Robin Extensions. If flexible numbering is done then
enter the Flexible number.
If the Flexible number is say 26 then XXX will be = 26 & not
026.
NN= The last 2 digits of the
1st Extension number (Not the flexible number
)
# 27 NN XXX Where, XXX= 3rd Extension number of Round Robin Extensions. If flexible numbering is done then
enter the Flexible number.
If the Flexible number is say 26 then XXX will be = 26 & not
026.
NN= The last 2 digits of the
2nd Extension number (Not the flexible number
)
# 27 NN XXX Where, XXX= 4th Extension number of Round Robin Extensions. If flexible numbering is done then
enter the Flexible number.
If the Flexible number is say 26 then XXX will be = 26 & not
026.
NN= The last 2 digits of the
3rd Extension number (Not the flexible number
)
Note
:
Round Robin Ring Assignment can be set in combination with Simultaneous Ring i.e., some extension would ring in
Simultaneous mode and some in Round Robin mode for the same Junction Line ring.
:
To enter many extensions without entering password again and again, following is an example for the procedure:
To assign Extension numbers 601, 602 & 605 to ring for incoming calls on Junction number 2, in
Day Mode:
Dial #
0000 + 30 + 2 # + 30 2 01 0 # + 30 2 02 0 # + 30 2 05 0 #
Example:
To assign Round Robin to 601, 602, 604 and then 603
Dial #
0000 + 3 0 1 #
#
0000 + 3 0 1 01 0 #
#27 01 602
#27 02 604
#27 04 603
Dial #
0000 + 3 0 2 #
#
0000 + 3 0 2 01 0 #
Dial #
0000 + 3 0 3 #
#
0000 + 3 0 3 01 0 #
Options when all assigned extensions are busy
When the extensions assigned for the Junction incoming call are busy, following options can be set:
Dial #
0000 + 1880# (The assigned extension when busy, will hear a waiting call beep after every 5 seconds)
This is the default setting.
Dial #
0000 + 1881#
(The call will land on the first available extension starting from 601, 602, …to … 632)
.
Junction - Enable / Disable
.
The PBX has auto detect feature whereby it detects whether a Junction line is connected on its Junction port or not.
As we connect a Junction line to the PBX, the corresponding Junction port gets Enabled. As we remove a Junction line, the
corresponding Junction port gets Disabled.
To avoid continuous glow of DSS keys of unused Junction ports, on KTS, assign the DSS keys to Extensions.
.
Junction to Junction Forwarding
.
Making 2 Junction lines talk to each other while Ext remains out of the conversation.
During conversation with a Junction line - Hook-Flash - # #
(To park the Call)
– 0 – Tel No (who is to be connected to the previous
Junction call)
– Hook Flash - # 6 - Now all 3 party can talk to each other but Ext can keep Handset down.
The 2 Junction lines will hear a tone after 80 seconds and if any of them presses * then they can talk for another 90 seconds. Like
this they can keep extending the talk time. If * is not pressed then the calls will disconnect. If they wish to disconnect in between
then any of them need to dial #.
