Note:
The above programming is true for SLT as well as KTS. However, KTS has an option to do the above through another
process given under the heading ‘KTS Features’.
.
Hold Music
.
The PBX can be connected to an external Music source or to an in-built Music for Hold Music.
In default, it is connected to internal Music source.
Programming to change the source
:
Dial #
0000 + 140 # for Internal source
Dial #
0000 + 141 # for External source
Dial #
0000 + 14 # to listen to the Music
The external Music source is to be terminated on the connector marked as “Music” on the backside of the PBX.
.
Hot Line
.
Some or all KTS/SLT extensions can be programmed to get Junction Line or an Operator on lifting the Handset.
To dial internal numbers from such extensions, dial
on lifting the Handset. You will get internal dial tone of the PBX.
Hot Line to Junction Line
To program an extension to get a free Junction line on lifting handset,
Dial #
0000 + 2 NN 0 #
Where, NN= last 2 digits of Extension numbers that is to be programmed for
Direct Junction Access.
Dial #
0000 + 20 # -
To convert all Extensions in “Hot Line to Junction” mode
Dial #
0000 + 2 NN 1 # - To convert NN Extension in normal mode.
Dial #
0000 + 21 # - To convert all Extensions in normal mode.
Hot Line to Operator
To program an extension to connect to Operator on lifting handset,
Dial #
0000 + 883 NN #
Where, NN= last 2 digits of Extension numbers that is to be programmed for this feature.
Dial #
0000 + 883 # - To convert all Extensions in Hot Line to Operator mode.
Dial #
0000 + 884NN # - To convert NN Extensions in normal mode.
Dial #
0000 + 884 # - To convert all Extensions in normal mode.
In case of Hot Line, following time delay can be set
:
Dial #
0000 + 189 TT #
Where, TT = 01
– 99 seconds. It is the time within which the extension can dial any extension/Junction number
on lifting handset. After this time is lapsed, it will ring as per the “Hot Line to Operator” setting.
Default = 00 Seconds
Note
:
When all Extensions are converted to Hot Line then to get into the Programming mode, lift Handset and
Dial
#
0000 + whatever Programming to be done.
:
To convert an extension from “Hot Line to Junction” to “Hot Line to Operator” or vice versa, first convert it to normal
mode.
.
Junction Access During Power Failure
.
When the system is switched OFF, the Junction lines get directly connected to following respective extensions.
Junction Number Extension Number to which it gets connected
01
605
02
606
03
607
04
608
05
609
06
610
07
611
08
612
In default first 4 Junction lines are defined for Night Facility on Extension number 605 to 608.
In case 8 Junction Lines are used, then set Switch no 1.3.5 & 7 of DIP Switch block on the Main CPU to OFF position.
In case of 4 Junction lines in the PBX, keep all switches to ON position.
.
Junction Access Code
.
Junction lines can be accessed in rotation by dialing 9.
To access a particular Junction line, dial #11, #12, #13, #14 … #18
(11 represents the first junction Line and 18 the last one).
.
Junction Access in Circular / Sequential Mode
.
In case of dialing out on the Junction Lines, PBX can be configured to work in either of the following 2 modes:
Mode Description
Circular When an extension dials 9, the PBX will allot Junction numbers 01.
Next time any Extension dial 9, Junction number 02 will be allotted. Then 03. Then 01.
