Carver Yachts 38 Super Sport, Руководство пользователя

Страница: 57 / 126

3827 • U2 3/10 1
I
nternal
S
yStemS
S
ectIon
4
Air Conditioning System
For the air conditioning system to operate, it needs a source of AC power
(supplied by either a shore power source or the generator) and a supply of
seawater (either salt or fresh).
The factory-installed air conditioning system consists of two air
conditioning units:
• A 16,000 BTU unit, located in a starboard cabinet aft of the dinette
seating to cools the dinette and forward stateroom.
• A 16,000 BTU unit, located beneath the master stateroom berth to
cool the master stateroom, master and forward heads.
Producing Heat
The air conditioning system can produce heat when it is operated in
reverse cycle mode. Reverse cycle operation, however, is affected by
the temperature of the seawater. As seawater temperature decreases
so does the air conditioning system’s ability to produce warm air. Carver
recommends that the air conditioning system not be operated in reverse
cycle mode when the seawater temperature is below 40˚F.
Powering the Air Conditioning
1. Make sure the air conditioning seacock is closed. Remove and clean the
air conditioning system’s seawater strainer. The strainer prevents debris
in the seawater from entering the air conditioning system.
2. Reinstall the seawater strainer. If the strainer leaks when the air
conditioning seacock is opened, close the seacock, then check the
strainer for correct installation.
3. Open the air conditioning seacock to supply seawater to the air conditioning
pump.
4. Supply AC power to your boat. Refer to Section 3 - Shore Power or
Generator Power to do this.
Because the air conditioning condensation drains into the sump, the Auto Sump
circuit breaker on the Safety Breaker Panel must be ON when the air conditioning
system is operating.
5. On the Safety Breaker Panel, make sure that the Auto Sump circuit
breaker is ON.
Do not run an air conditioning system’s water pump when the seacock that supplies
seawater to the system is closed. Operating the pump with no seawater can damage
it.
6. On the AC Control Center:
a. Switch the Air Conditioning System Water Pump circuit breaker ON.
b. Switch the desired Air Conditioning Unit circuit breakers ON.
7. Verify that seawater is being pumped through the air conditioning units.
As the seawater exits the units, it flows out of a single discharge thru-
hull fitting.
Air Conditioning System
For the air conditioning system to operate, it needs a source of AC power
(supplied by either a shore power source or the generator) and a supply of
seawater (either salt or fresh).
The factory-installed air conditioning system consists of two air
conditioning units:
• A 16,000 BTU unit, located in a starboard cabinet aft of the dinette
seating to cools the dinette and forward stateroom.
• A 16,000 BTU unit, located beneath the master stateroom berth to
cool the master stateroom, master and forward heads.
Producing Heat
The air conditioning system can produce heat when it is operated in
reverse cycle mode. Reverse cycle operation, however, is affected by
the temperature of the seawater. As seawater temperature decreases
so does the air conditioning system’s ability to produce warm air. Carver
recommends that the air conditioning system not be operated in reverse
cycle mode when the seawater temperature is below 40˚F.
Powering the Air Conditioning
1. Make sure the air conditioning seacock is closed. Remove and clean the
air conditioning system’s seawater strainer. The strainer prevents debris
in the seawater from entering the air conditioning system.
2. Reinstall the seawater strainer. If the strainer leaks when the air
conditioning seacock is opened, close the seacock, then check the
strainer for correct installation.
3. Open the air conditioning seacock to supply seawater to the air conditioning
pump.
4. Supply AC power to your boat. Refer to Section 3 - Shore Power or
Generator Power to do this.
Because the air conditioning condensation drains into the sump, the Auto Sump
circuit breaker on the Safety Breaker Panel must be ON when the air conditioning
system is operating.
5. On the Safety Breaker Panel, make sure that the Auto Sump circuit
breaker is ON.
Do not run an air conditioning system’s water pump when the seacock that supplies
seawater to the system is closed. Operating the pump with no seawater can damage
it.
6. On the AC Control Center:
a. Switch the Air Conditioning System Water Pump circuit breaker ON.
b. Switch the desired Air Conditioning Unit circuit breakers ON.
7. Verify that seawater is being pumped through the air conditioning units.
As the seawater exits the units, it flows out of a single discharge thru-
hull fitting.
Open Closed
https://www.boat-manuals.com/