Canon imageRUNNER ADVANCE 6075 Series, Руководство по обслуживанию

Страница: 991 / 1406

8
8
8-209
8-209
Service Mode > SORTER > ADJUST
Service Mode > SORTER > ADJUST
SORTER > ADJUST
STP-R4 LTRR rear stpl pstn (<45 deg): Fin-E1
Lv.1 Details To adjust the one rear staple position on the LTRR size paper.
As the value is incremented by 1, the staple position moves to the
rear side by 0.49mm.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When misalignment occurs at the rear staple position on LTRR size
paper
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
-6 to 6
Unit 0.49 mm
Appropriate target value 0
Default value
0
SW-UP-RL Adj Swing Roller falling pstn: Fin-E1
Lv.1 Details To adjust the Swing Roller fall position.
As the value is incremented by 1, the Swing Roller fall position
moves downward by 0.2mm.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When paper fails to be transported to the Processing Tray and
misalignment occurs
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
-17 to 33
Unit 0.2 mm
Appropriate target value 0
Default value
0
PUN-V-RG Adj punch vertical rgst pstn: Fin-E1
Lv.1 Details To adjust the vertical registration position of the paper to be punched.
As the value is incremented by 1, the punch hole position moves
toward the edge by 1mm.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When misalignment of punch hole position occurs
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
-4 to 2
Unit 1 mm
Appropriate target value 0
Default value
0
SORTER > ADJUST
PRCS-RET Adj Process Tray return amount:Fin-E1
Lv.1 Details To adjust the pull-back amount of the paper on the Processing Tray.
As the value is incremented by 1, the amount to return papers to the
Process Tray Stopper is increased by 1.4 mm (paper feed amount of
the Swing Roller is increased).
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When the paper is bent in the Processing Tray
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 5
Unit 1.4 mm
Appropriate target value 0
Default value
0
UP-CL Upward curl prevention mode: Fin-E1
Lv.1 Details Set 1 when upward curl occurs on the paper delivered to the Stack
Tray, and paper leaning due to the curl occurs.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When upward curl occurs on the paper delivered to the Stack Tray,
and paper leaning due to the curl occurs
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 1
0: OFF, 1: ON
Default value 0
DW-CL Downward curl prevention mode: Fin-E1
Lv.1 Details Set 1 when downward curl occurs on the paper delivered to the
Stack Tray, and paper leaning due to the curl occurs.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When downward curl occurs on the paper delivered to the Stack
Tray, and paper leaning due to the curl occurs
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 1
0: OFF, 1: ON
Default value 0