manualshive.com logo in svg

Canon ImageRunner 4045, Список кодов ошибок

Поделиться
Скачать
Canon ImageRunner 4045 Скачать руководство пользователя страница 84

84 

 

the host machine and the 
Finisher was lost. 

E717-
0001 

Communication error with 
the NE Controller 
Error when the NE 
Controller is started. The 
NE Controller which was 
connected before turning 
OFF the power is not 
connected at power-on. 

Check the cable, and then go through the following to 
clear the error: Service Mode > COPIER > 
FUNCTION > CLEAR > ERR. 

E717-
0002 

Communication error with 
the NE Controller 
IPC error at NE Controller 
operation. Open circuit of 
IPC, unable to recover 
the IPC communication. 

Check the cable, and then go through the following to 
clear the error: Service Mode > COPIER > 
FUNCTION > CLEAR > ERR. 

E719-
0001 

Error in coin manager 
Error when the coin 
manager is started. The 
coin manager which was 
connected before turning 
OFF the power is not 
connected at power-on. 

Check the cable, and then go through the following to 
clear the error: Service Mode > COPIER > 
FUNCTION > CLEAR > ERR. 

E719-
0002 

Error in coin manager 
IPC error at coin manager 
operation. Open circuit of 
IPC, unable to recover 
the IPC communication. 
When open circuit of the 
pickup/delivery signal 
cable is detected. Invalid 
connection is detected. 

Check the cable, and then go through the following to 
clear the error: Service Mode > COPIER > 
FUNCTION > CLEAR > ERR. 

E719-
0003 

Error in coin manager 
Communication error with 
the coin manager occurs 
during unit price 
acquisition at startup. 

Check the cable, and then go through the following to 
clear the error: Service Mode > COPIER > 
FUNCTION > CLEAR > ERR. 

E719-
0011 

Error when the Card 
Reader is started 
The Card Reader which 
was connected before 
turning OFF the power is 
not connected at power-

Check the cable, and then go through the following to 
clear the error: Service Mode > COPIER > 
FUNCTION > CLEAR > ERR. 

Содержание ImageRunner 4045































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды