manualshive.com logo in svg

Canon ImageRunner 4045, Список кодов ошибок

Поделиться
Скачать
Canon ImageRunner 4045 Скачать руководство пользователя страница 13

13 

 

E505-
0002 

EEPROM error 
The checksum data for the 
EEPROM on the punch controller 
PCB has an error. 

Replace the Punch Controller PCB. 

E514-
8001 

Rear end assist home position 
error 
The stapler does not leave the 
rear end assist home position 
when the Rear End Assist Motor 
has been driven for 3 seconds. 

1. The Rear End Assist Home Position 
Sensor (PI109) is faulty. 2. The wiring 
between the Finisher Controller PCB and 
Rear End Assist Motor is faulty. 3. The end 
assist mechanism is faulty. 4. The Rear End 
Assist Motor (M109) is faulty. 5. The Finisher 
Controller PCB is faulty. 

E514-
8002 

Rear end assist home position 
error 
The stapler does not return to the 
rear end assist home position 
when the Rear End Assist Motor 
has been driven for 3 seconds. 

1. The Rear End Assist Home Position 
Sensor (PI109) is faulty. 2. The wiring 
between the Finisher Controller PCB and 
Rear End Assist Motor is faulty. 3. The end 
assist mechanism is faulty. 4. The Rear End 
Assist Motor (M109) is faulty. 5. The Finisher 
Controller PCB is faulty 

E520-
0001 

Shift Motor fails to move from HP 
At initial rotation, when the Motor 
rotates for specified period of time 
and cannot move from HP, it is 
detected as an error if the same 
symptom occurs again after the 
first retry. 

1. Check if the Motor (M4) Connector is 
physically removed. 2. Check if the Motor 
failure occurs. 3. Check if the Shift Roller HP 
Sensor (S2) Connector is physically 
removed. 4. Check if the Shift Roller HP 
Sensor (S2) failure occurs. 

E520-
0002 

Shift Motor fails to return to HP 
At initial rotation, when the Motor 
rotates for specified period of time 
and cannot return to HP, it is 
detected as an error if the same 
symptom occurs again after the 
first retry. 

1. Check if the Motor (M4) Connector is 
physically removed. 2. Check if the Motor 
failure occurs. 3. Check if the Shift Roller HP 
Sensor (S2) Connector is physically 
removed. 4. Check if the Shift Roller HP 
Sensor (S2) failure occurs. 

E530-
8001 

Front aligning plate home position 
error 
The aligning plate does not leave 
the aligning plate front home 
position sensor when the 
alignment plate front motor has 
been driven for 4 seconds. 

1. The front aligning plate home position 
sensor (PI106) is faulty. 2. The wiring 
between the finisher controller PCB and 
front aligning plate motor is faulty. 3. The 
front aligning plate is faulty. 4. The front 
aligning plate motor (M103) is faulty. 5. The 
finisher controller PCB is faulty. 

E530-
8002 

Front aligning plate home position 
error 
The aligning plate does not return 
to aligning plate front home 

1. The front aligning plate home position 
sensor (PI106) is faulty. 2. The wiring 
between the finisher controller PCB and 
front aligning plate motor is faulty. 3. The 

Содержание ImageRunner 4045































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды