manualshive.com logo in svg

Canon ImageRunner 4045, Список кодов ошибок

Поделиться
Скачать
Canon ImageRunner 4045 Скачать руководство пользователя страница 77

77 

 

(Finisher-E1) 

Finisher Controller PCB and Stack Ejection Motor, 
and between the Finisher Controller PCB and 
Shutter Clutch is faulty. 3. The positioning plate 
drive mechanism is faulty. 4. The Paper 
Positioning Plate Motor (M4) is faulty. 5. The 
Saddle Stitcher Controller PCB is faulty. 

E5F1-
8001 

Paper Ffolding Motor lock 
error (Finisher-E1) 
The feed speed of the paper 
fold roller reaches 5 mm/sec 
or less. 

1. The Paper Folding Motor Clock Sensor (PI4) 
and Paper Ffolding Home Position Sensor (PI21) 
is faulty. 2. The paper folding roller drive 
mechanism is faulty. 3. The Paper Folding Motor 
(M2) is faulty. 4. The Saddle Stitcher Controller 
PCB is faulty. 

E5F1-
8002 

Paper positioning plate 
home position error 
(Finisher-E1) 
The status of the Paper Fold 
Home Position Sensor does 
not change when the paper 
fold Motor has been driven 
for 3 seconds. 

1. The Paper Folding Motor Clock Sensor (PI4) 
and Paper Ffolding Home Position Sensor (PI21) 
is faulty. 2. The paper folding roller drive 
mechanism is faulty. 3. The Paper Folding Motor 
(M2) is faulty. 4. The Saddle Stitcher Controller 
PCB is faulty. 

E5F2-
8001 

Guide home position error 
(Finisher-E1) 
The Guide Home Position 
Sensor does not turn ON 
when the Guide Motor has 
been driven for 700 pulses. 

1. The Guide Home Position Sensor (PI13) is 
faulty. 2. The guide plate drive mechanism is 
faulty. 3. The Guide Motor (M3) is faulty. 4. The 
Saddle Stitcher Controller PCB is faulty. 

E5F2-
8002 

Guide home position error 
(Finisher-E1) 
The Guide Home Position 
Sensor does not turn OFF 
when the Guide Motor has 
been driven for 50 pulses. 

1. The Guide Home Position Sensor (PI13) is 
faulty. 2. The guide plate drive mechanism is 
faulty. 3. The Guide Motor (M3) is faulty. 4. The 
Saddle Stitcher Controller PCB is faulty. 

E5F3-
8001 

Aligning plate home position 
error (Finisher-E1) 
The Aligning Plate Home 
Position Sensor does not 
turn ON when the Aligning 
Motor has been driven for 
500 pulses. 

1. The Aligning Plate Home Position Sensor (PI5) 
is faulty. 2. The aligning plate drive mechanism is 
faulty. 3. The Aligning Motor (M5) is faulty. 4. The 
Saddle Stitcher Controller PCB is faulty. 

E5F3-
8002 

Aligning plate home position 
error (Finisher-E1) 
The Aligning Plate Home 
Position Sensor does not 

1. The Aligning Plate Home Position Sensor (PI5) 
is faulty. 2. The aligning plate drive mechanism is 
faulty. 3. The Aligning Motor (M5) is faulty. 4. The 
Saddle Stitcher Controller PCB is faulty. 

Содержание ImageRunner 4045































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды