manualshive.com logo in svg

Canon ImageRunner 4045, Список кодов ошибок

Поделиться
Скачать
Canon ImageRunner 4045 Скачать руководство пользователя страница 78

78 

 

turn OFF when the Aligning 
Motor has been driven for 50 
pulses. 

E5F4-
8001 

Stitcher (rear) home position 
error (Finisher-E1) 
The Stitcher Home Position 
Sensor does not turn ON 
when the Stitch Motor (rear) 
has been driven backward 
for 0.5 sec. 

1. The Stitcher Home Position Sensor (rear) 
(SW5) is faulty. 2. The Stitcher (rear) is faulty. 3. 
The Saddle Stitcher Controller PCB is faulty. 

E5F4-
8002 

Stitcher (rear) home position 
error (Finisher-E1) 
The stitching home position 
Sensor does not turn OFF 
when the Stitch Motor (rear) 
has been driven forward for 
0.5 sec. 

1. The Stitcher Home Position Sensor (rear) 
(SW5) is faulty. 2. The Stitcher (rear) is faulty. 3. 
The Saddle Stitcher Controller PCB is faulty. 

E5F5-
8001 

Stitcher (front) home position 
error (Finisher-E1) 
The Stitcher Home Position 
Sensor does not turn ON 
when the Stitch Motor (front) 
has been driven forward for 
0.5 sec. 

1. The Stitcher Home Position Sensor (front) 
(SW7) is faulty. 2. The Stitcher (front) is faulty. 3. 
The Saddle Stitcher Controller PCB is faulty. 

E5F5-
8002 

Stitcher (front) home position 
error (Finisher-E1) 
The Stitcher Home Position 
Sensor does not turn OFF 
when the Stitch Motor (front) 
has been driven backward 
for 0.5 sec. 

1. The Stitcher Home Position Sensor (front) 
(SW7) is faulty. 2. The Stitcher (front) is faulty. 3. 
The Saddle Stitcher Controller PCB is faulty. 

E5F6-
8001 

Paper pushing plate home 
position error (Finisher-E1) 
The Paper Pushing Plate 
Home Position Sensor does 
not turn ON when the Paper 
Pushing Plate Motor has 
been driven for 0.5 sec. 

1. The Paper Pushing Plate Home Position 
Sensor (PI14), Paper Pushing Plate Top Position 
Sensor (PI15), and Paper Pushing Plate Motor 
Clock Sensor (PI1) is faulty. 2. The paper pushing 
plate drive mechanism is faulty. 3. The Paper 
Pushing Plate Motor (M8) is faulty. 4. The Saddle 
Stitcher Controller PCB is faulty. 

E5F6-
8002 

Paper pushing plate home 
position error (Finisher-E1) 
The Paper Pushing Plate 
Home Position Sensor does 
not turn OFF when the 

1. The Paper Pushing Plate Home Position 
Sensor (PI14), Paper Pushing Plate Top Position 
Sensor (PI15), and Paper Pushing Plate Motor 
Clock Sensor (PI1) is faulty. 2. The paper pushing 
plate drive mechanism is faulty. 3. The Paper 

Содержание ImageRunner 4045































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды