manualshive.com logo in svg

Canon ImageRunner 4045, Список кодов ошибок

Поделиться
Скачать
Canon ImageRunner 4045 Скачать руководство пользователя страница 29

29 

 

the error retry after the communication 
failure with the finisher. 

E713-
0001 

Erroneous communication with finisher 
(transmission retry error) 
The communication does not restart by 
the error retry after the communication 
failure with the finisher 

1. Check the cable. 2. Replace the DC 
Controller PCB (UN2). 3. Replace the 
Finisher Controller PCB. 

E713-
0002 

Erroneous communication with finisher 
(transmission data error) 
The communication does not restart by 
the error retry after the communication 
failure with the finisher. 

1. Check the cable. 2. Replace the DC 
Controller PCB (UN2). 3. Replace the 
Finisher Controller PCB. 

E713-
0004 

Erroneous communication with finisher 
(reception error) 
The communication does not restart by 
the error retry after the communication 
failure with the finisher. 

1. Check the cable. 2. Replace the DC 
Controller PCB (UN2). 3. Replace the 
Finisher Controller PCB. 

E713-
0010 

Erroneous communication with finisher 
(reception error)  
The communication does not restart by 
the error retry after the communication 
failure with the finisher. 

1. Check the cable. 2. Replace the DC 
Controller PCB (UN2). 3. Replace the 
Finisher Controller PCB. 

E713-
0011 

Erroneous communication with finisher 
(reception error) 
The communication does not restart by 
the error retry after the communication 
failure with the finisher. 

1. Check the cable. 2. Replace the DC 
Controller PCB (UN2). 3. Replace the 
Finisher Controller PCB. 

E713-
0020 

Erroneous communication with finisher 
(reception data error) 
The communication does not restart by 
the error retry after the communication 
failure with the finisher. 

1. Check the cable. 2. Replace the DC 
Controller PCB (UN2). 3. Replace the 
Finisher Controller PCB. 

E713-
0021 

Erroneous communication with finisher 
(reception time out error) 
The communication does not restart by 
the error retry after the communication 
failure with the finisher. 

1. Check the cable. 2. Replace the DC 
Controller PCB (UN2). 3. Replace the 
Finisher Controller PCB. 

E713-
0022 

Erroneous communication with finisher 
(reception data error) 
The communication does not restart by 
the error retry after the communication 
failure with the finisher. 

1. Check the cable. 2. Replace the DC 
Controller PCB (UN2). 3. Replace the 
Finisher Controller PCB. 

Содержание ImageRunner 4045































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды