manualshive.com logo in svg

Canon ImageRunner 4045, Список кодов ошибок

Поделиться
Скачать
Canon ImageRunner 4045 Скачать руководство пользователя страница 42

42 

 

E017-
0001 

ETB disengagement error 
Disengagement of the ETB 
is not completed within the 
specified period of time. 

1. Check the connection of the ETB Disengage 
Sensor (PS56). Sensor side: J2101, J3270, PCB 
side: J343 (Duplex Driver PCB (PCB4)) 2. Check 
the connection of the Duplex Feed Left Motor 
(M19). Motor side: J2107, J3044 (relay), PCB 
side: J330 (Duplex Driver PCB (PCB4)) 3. 
Replace the ETB Disengage Sensor (PS56). 4. 
Replace the Duplex Feed Left Motor (M19). 5. 
Replace the Duplex Driver PCB (PCB4). 6. 
Replace the DC Controller PCB (PCB1). NOTE: 
Check if the Disengagement Cam is stained. If 
necessary, clean it. Check if the drive system 
(gear, Motor, one-way) is failed. If necessary, 
replace it. Check if the link with the Fixing Feed 
Handle is failed. If necessary, replace it. 

E017-
0002 

ETB engagement error 
Engagement of the ETB is 
not completed within the 
specified period of time. 

1. Check the connection of the ETB Disengage 
Sensor (PS55). Sensor side: J2100, J3270, PCB 
side: J343 (Duplex Driver PCB (PCB4)) 2. Check 
the connection of the Duplex Feed Left Motor 
(M19). Motor side: J2107, J3044 (relay), PCB 
side: J330 (Duplex Driver PCB (PCB4)) 3. 
Replace the ETB Engage Sensor (PS55). 4. 
Replace the Duplex Feed Left Motor (M19). 5. 
Replace the Duplex Driver PCB (PCB4). 6. 
Replace the DC Controller PCB (PCB1). NOTE: 
Check if the Disengagement Cam is stained. If 
necessary, clean it. Check if the drive system 
(gear, Motor, one-way) is failed. If necessary, 
replace it. Check if the link with the Fixing Feed 
Handle is failed. If necessary, replace it. 

E017-
0003 

ETB HP error 
Engagement of the ETB was 
not completed at 
initialization. 

If this error occurs at installation, the ETB 
Disengage Member (Transfer Frame Stopper) 
may be left unremoved. Refer to the 
troubleshooting "Remedy to be implemented 
when the ETB Disengage Member (Transfer 
Frame Stopper) is left unremoved" in the Service 
Manual, and check whether the ETB Disengage 
Member is left unremoved or not and implement 
appropriate procedure. If this error occurs at times 
other than installation, follow the following steps to 
implement check and remedy. 1. Check the 
connection of the ETB Disengage Sensor (PS56). 
Sensor side: J2101, J3270, PCB side: J343 
(Duplex Driver PCB (PCB4)) 2. Check the 
connection of the Duplex Feed Left Motor (M19). 

Содержание ImageRunner 4045































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды