manualshive.com logo in svg

Canon ImageRunner 4045, Список кодов ошибок

Поделиться
Скачать
Canon ImageRunner 4045 Скачать руководство пользователя страница 4

4 

 

0000 

and the developing assembly is 
clogged with toner. 
The Developing Assembly Toner 
Sensor (S25) detects the absence 
of toner, while the Sub Hopper 
Toner Sensor (S26) detects the 
presence of toner. With the 
Developing Cylinder Clutch (CL3) 
turned on, the hopper feed screw 
motor (M16) is rotated for 1 sec 
intermittently 194 times; still, the 
Developing Assembly Toner 
Sensor (S25) does not detect the 
presence of toner. * Error occurs 
after the delivery if a paper in 
passage exists. 

gear. (If rotating, false detection by the 
sensor is doubted. Feed the toner to the 
developing unit in service mode: 
COPIER > FUNCTION > INSTALL > 
TONER-S.) 2. Replace the Developing 
Assembly Toner Sensor (S25). 3. 
Replace the Sub Hopper Toner Sensor 
(S26). 4. Replace the DC Controller PCB 
(UN2). 

E024-
0000 

The connector of Developing 
Assembly Toner Sensor (S25) is 
disconnected. 
The Developing Assembly Toner 
Sensor (S25) connection detection 
signal is absent for 100 msec 10 
times in sequence. * Error occurs 
after the delivery if a paper in 
passage exists. 

1. Check connection of the Connector 
(J2013/J209). 2. Replace the Developing 
Assembly Toner Sensor (S25). 3. 
Replace the DC Controller PCB (UN2). 

E024-
0001 

The Developing Assembly Toner 
Sensor (S25) is disconnected. 
<At LOW SPEED> The Developing 
Assembly Toner Sensor (S25) ON 
counter is checked every 2.5 
seconds, and the counter 
increments 1 count every 25 times 
when the sensor goes on, and 300 
counts are reached. <At HIGH 
SPEED> The Developing 
Assembly Toner Sensor (S25) ON 
counter is checked every 1.5 
seconds, and the counter 
increments 1 count every 15 times 
when the sensor goes on, and 300 
counts are reached. 

1. Check connection of the Connector 
(J2013/J209). 2. Replace the Developing 
Assembly Toner Sensor (S25). 3. 
Replace the DC Controller PCB (UN2). 

E025-
0000 

The connector of Sub Hopper 
Toner Sensor (S26) is 
disconnected. 
The Sub Hopper Toner Sensor 

1. Check connection of the Connector 
(J2115/J2503/J207). 2. Replace the Sub 
Hopper Toner Sensor (S26). 3. Replace 
the DC Controller PCB (UN2). 

Содержание ImageRunner 4045































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды