manualshive.com logo in svg

Canon ImageRunner 4045, Список кодов ошибок

Поделиться
Скачать
Canon ImageRunner 4045 Скачать руководство пользователя страница 67

67 

 

The Stapler does not leave the 
swing home position when the 
Swing Motor has been driven for 3 
seconds. 

Finisher Controller PCB and Swing Motor is 
faulty. 3. The swing mechanism is faulty. 4. 
The Swing Motor (M106) is faulty. 5. The 
Finisher Controller PCB is faulty. 

E535-
8002 

Swing home position error 
(Finisher-E1) 
The Stapler does not return to the 
swing home position when the 
Swing Motor has bee driven for 3 
seconds. 

1. The Swing Home Position Sensor 
(PI105) is faulty. 2. The wiring between the 
Finisher Controller PCB and Swing Motor is 
faulty. 3. The swing mechanism is faulty. 4. 
The Swing Motor (M106) is faulty. 5. The 
Finisher Controller PCB is faulty. 

E537-
8001 

Rear aligning plate home position 
error (Finisher-E1) 
The aligning plate does not leave 
the Aligning Plate Rear Home 
Position Sensor when the 
Alignment Plate Rear Motor has 
been driven for 4 seconds. 

1. The Aligning Plate Rear Home Position 
Sensor (PI107) is faulty. 2. The wiring 
between the Finisher Controller PCB and 
Aligning Plate Rear Motor is faulty. 3. The 
rear aligning plate is faulty. 4. The Rear 
Aligning Plate Motor (M104) is faulty. 5. 
The Finisher Controller PCB is faulty. 

E537-
8002 

Rear aligning plate home position 
error (Finisher-E1) 
The aligning plate does not return 
to Aligning Plate Rear Home 
Position Sensor when the 
Alignment Plate Rear Motor has 
been driven for 4 seconds. 

1. The Aligning Plate Rear Home Position 
Sensor (PI107) is faulty. 2. The wiring 
between the Finisher Controller PCB and 
Aligning Plate Rear Motor is faulty. 3. The 
rear aligning plate is faulty. 4. The Rear 
Aligning Plate Motor (M104) is faulty. 5. 
The Finisher Controller PCB is faulty. 

E540-
8001 

Tray 1 time out error (Finisher-E1) 
1. If the tray does not return to 
home position when the Tray 1 
Shift Motor is driven for 25 
seconds. 2. If the tray does not 
move to other area when Tray 1 
Shift Motor is driven for 5 seconds. 

1. The Tray 1 Shift Area Sensor PCB is 
faulty. 2. The wiring between the Finisher 
Controller PCB and Tray 1 Shift Motor is 
faulty. 3. The tray up/down mechanism is 
faulty. 4. The Tray 1 Shift Motor (M107) is 
faulty. 5. The Finisher Controller PCB is 
faulty. 

E540-
8002 

Tray 1 shift area error (Finisher-E1) 
1. The dangerous area is reached 
before the Tray 1 Paper Surface 
Sensor detects paper surface 
during the paper surface detection 
operation. 2. A discontinuous area 
is detected during tray operation. 

1. The Tray 1 Shift Area Sensor PCB is 
faulty. 2. The wiring between the Finisher 
Controller PCB and Tray 1 Shift Motor is 
faulty. 3. The tray up/down mechanism is 
faulty. 4. The Tray 1 Shift Motor (M107) is 
faulty. 5. The Finisher Controller PCB is 
faulty. 

E540-
8003 

Swing Guide Switch/Staple Safety 
Switch error (Finisher-E1) 
The swing guide switch or staple 
safety switch is activated while the 
tray is operating. 

1. The Tray 1 Shift Area Sensor PCB is 
faulty. 2. The wiring between the Finisher 
Controller PCB and Tray 1 Shift Motor is 
faulty. 3. The tray up/down mechanism is 
faulty. 4. The Tray 1 Shift Motor (M107) is 

Содержание ImageRunner 4045































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды