manualshive.com logo in svg

Canon ImageRunner 4045, Список кодов ошибок

Поделиться
Скачать
Canon ImageRunner 4045 Скачать руководство пользователя страница 32

32 

 

E730-
A006 

PDL communication error 
No reply from PDL. Due 
to failure of Subbootable, 
or no existence, there is 
no reply from PDL. 

1. PDL reset processing. 2. Turn OFF and then ON 
the power. 3. Check the connection of the Main 
Controller PCB. 4. Reinstall the firmware. 5. Replace 
the Main Controller PCB. 

E730-
A007 

Mismatched PDL version 
Version of the host 
machine control software 
and version of PDL 
control software are 
different 

1. PDL reset processing. 2. Turn OFF and then ON 
the power. 3. System All Format and installation. 

 

Code 

Description 

Remedy 

E730-
B013 

PDL embedded font error 
Font data is corrupted. 

1. Turn OFF and then ON the power. 
2. Reinstall the system. 3. System All 
Format and installation. 

E732-
0000 

Reader communication error 
Negotiation failure. 

1. Check the connection of the 
Connector with the Reader. 2. Check 
the power of the Reader (check if the 
initialization operation is executed at 
startup). 3. Replace the Reader 
Controller PCB and the Main 
Controller PCB. 

E732-
0001 

Reader communication error 
Communication error. 

1. Check the connection of the 
Connector with the Reader. 2. Check 
the power of the Reader (check if the 
initialization operation is executed at 
startup). 3. Replace the Reader 
Controller PCB and the Main 
Controller PCB. 

E732-
0010 

Reader communication error 
Unable to detect Vsync from the Reader 
Controller although 2 minutes have 
passed after the completion of register 
setting of the Main Controller. 

1. Check the connection of the 
Connector with the Reader. 2. Check 
the power of the Reader (check if the 
initialization operation is executed at 
startup). 3. Replace the Reader 
Controller PCB and the Main 
Controller PCB. 

E732-
0021 

Reader communication error 
Communication error 

1. Check the connection of the 
Connector with the Reader. 2. Check 
the power of the Reader (check if the 
initialization operation is executed at 
startup). 3. Replace the Reader 

Содержание ImageRunner 4045































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды