manualshive.com logo in svg

Canon ImageRunner 4045, Список кодов ошибок

Поделиться
Скачать
Canon ImageRunner 4045 Скачать руководство пользователя страница 2

2 

 

Code 

Description 

Remedy 

E000-
0001 

Fixing temperature abnormal rise 
The temperature detected by the 
main thermistor does not rise to 
the specified value during startup 
control. 

1. Go through the following to clear the 
error: COPIER> FUNCTION> CLEAR> 
ERR; and then turn OFF and then ON 
the power. 2. Check connection of the 
Connectors (Thermistor Connector: 
J2063/J2510/J214, AC Connector: J105). 
3. Replace the Fixing Main Thermistor 
(Film Unit). 4. Replace the Fixing Main 
Unit. 5. Replace the DC Controller PCB 
(UN2). 

E001-
0000 

Fixing unit temperature rise 
detection 
The reading of the main thermistor 
is 250 deg C or more continuously 
for 200 msec. 

1. Go through the following to clear the 
error: COPIER> FUNCTION> CLEAR> 
ERR; and then turn OFF and then ON 
the power. 2. Check connection of the 
Connectors (Thermistor Connector: 
J2063/J2510/J214, AC Connector: J105). 
3. Replace the Fixing Main Thermistor 
(Film Unit). 4. Replace the Fixing Main 
Unit. 5. Replace the DC Controller PCB 
(UN2). 

E001-
0001 

Fixing unit temperature rise 
detection 
The hardware circuit detects 
overheating of the main or sub 
thermistor for 30 msec. 

1. Go through the following to clear the 
error: COPIER> FUNCTION> CLEAR> 
ERR; and then turn OFF and then ON 
the power. 2. Replace the DC Controller 
PCB (UN2). 

E001-
0002 

Fixing unit temperature rise 
detection 
The reading of the sub thermistor 
is 295 deg C or more continuously 
for 200 msec. 

1. Go through the following to clear the 
error: COPIER> FUNCTION> CLEAR> 
ERR; and then turn OFF and then ON 
the power. 2. Check connection of the 
Connectors (Thermistor Connector: 
J2063/J2510/J214, AC Connector: J105). 
3. Replace the Fixing Main Thermistor 
(Film Unit). 4. Replace the Fixing Main 
Unit. 5. Replace the DC Controller PCB 
(UN2). 

E002-
0000 

Fixing unit temperature insufficient 
rise 
1. The reading of the main 
thermistor is less than 115 deg C 
continuously for 400 msec 2.5 sec 
after it has indicated 100 deg C. 2. 
The reading of the main thermistor 

1. Go through the following to clear the 
error: COPIER> FUNCTION> CLEAR> 
ERR; and then turn OFF and then ON 
the power. 2. Check connection of the 
Connectors (Thermistor Connector: 
J2063/J2510/J214, AC Connector: J105). 
3. Replace the Fixing Main Thermistor 

 

 

Содержание ImageRunner 4045































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды