Canon ImageRunner 4045 Скачать руководство пользователя страница 28

Страница: 28 / 94

Code

Description

Remedy

E677-
0004

Print server error
CPU Fan operation error on the print
server is detected.

1. Check power supply to the CPU
Fan. 2. Replace the CPU Fan.

E677-
0010

Print server error
Not proper print server is connected.

Replace the print server with the
proper one.

E677-
0080

Print server error
Communication error at startup.

Check the cable connection,
reinstallation.

E710-
0001

Printer IPC error
Error is detected by IPC communication
IC of the printer engine at power ON.

Disconnection of cable.

E711-
0001

UFDI communication error
Communication system error (reception
time out error/ checksum error etc.)

1. Check the cable. 2. Replace the DC
Controller PCB (UN2). 3. Replace the
Finisher Controller PCB.

E711-
0002

IPC communication error
Communication system error (packet
error occurs without the request of
initialization)

1. Check the cable. 2. Replace the DC
Controller PCB (UN2). 3. Replace the
Finisher Controller PCB.

E713-
0000

Erroneous communication with finisher
(retry error)
The communication does not restart by

1. Check the cable. 2. Replace the DC
Controller PCB (UN2). 3. Replace the
Finisher Controller PCB

saved on SRAM cannot be read,
the phenomenon that the
communication is repeated occurs.

E615-
0001

Self test error of encryption module
A self test of the Ipsec Board was
conducted, and an error was
detected. The encryption module is
broken.

Upgrade the system after HDD format.
When this error occurs, normal network
communication cannot be guaranteed.

E674

FAX error

Check the cable connection, replace the
FAX PCB, replace the Main Controller
PCB.

E677-
0001

Print server error
Exhaust Fan operation error on the
print server is detected.

1. Check power supply to the Exhaust
Fan. 2. Replace the Exhaust Fan.

E677-
0003

Print server error
Error is detected at the
configuration check performed at
startup

Check the cable connection,
reinstallation.

Содержание ImageRunner 4045































































































Результаты поиска

Содержание ImageRunner 4045

Отзывы:

Бренды по названию

Популярные бренды

Canon ImageRunner 4045, Список кодов ошибок

Результаты поиска

Содержание ImageRunner 4045

Отзывы:

Бренды по названию

Популярные бренды