BYD ATTO 3 2022 Скачать руководство пользователя страница 87

Страница: 87 / 201

2. Stopping charging

• Charging stops when the battery is

fully charged.

• To stop earlier, first disconnect the

charging port by pressing the door

handle microswitch while carrying the

smart key and pulling out the charging

coupler.

REMINDER

•To unlock the vehicle, press the key

unlock button (OFF when charging)

or the door handle microswitch while

carrying the smart key.

•When anti-theft is enabled, unlock

the vehicle before pulling out the

charging coupler to disable the

charging port electric lock. The

coupler has to be pulled out within 30

seconds, or the port will re-lock.

•The electric lock mode can be setup

through the →

New Energy

→

Charge Settings

interface. For setup

procedure details, see Charge Port

Electric Lock Control function.

•If the charging coupler cannot be

removed after unlocking, a few more

unlocking attempts can be tried. If it

still cannot be removed, emergency

unlocking can be tried. Refer to the

charging port emergency unlocking

procedure in the lock control.

• Disconnect the power plug.

• Reinsert the cover and close the port

hatch.

• Store the charging equipment properly.

REMINDER

•If the charging port plug is fully open,

do not close the hatch.

WARNING

•

Never drop the Mode 2 equipment.

Never move it by pulling it directly by

its cable. When moving the device, it

needs to be handled with care. Never

move it by pulling it directly by its

cable.

AC Charging Pile Charging*

1. Equipment description

• Single-phase AC charging box*

• Use a certified household charging

box. For details, refer to the instruction

manual and follow the operating

steps.

• Single-phase AC charging box: this

equipment includes a charging box,

a connector and a connecting cable.

For information on circuit breaker and

emergency stop switch, refer to the

charging box instruction manual.

Содержание ATTO 3 2022










































































































































































































Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды

BYD ATTO 3 2022, Руководство пользователя

Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды