BYD ATTO 3 2022 Скачать руководство пользователя страница 84

Страница: 84 / 201

USING AND DRIVING

General Charging Faults and Solutions

Fault

Possible Cause

Solution

Charger is

connected, charge

starts, but battery

will not charge.

Charging card in arrears

or faulty charging pile.

Consult card balance or contact charging

station staff.

AC charging connector

not properly plugged in.

Ensure the charger switch has come up. Check

cable length and connection position.

Low 12 V battery SOC

Connect the vehicle to another 12 V battery to

charge its own 12 V batteries after powering

on.

The local standard

socket has no power

supply.

Ensure the power supply is under overload

protection. Use the corresponding charging

power supply, i.e., standard 220 V 50 Hz 10 A

single-phase two-pole grounded socket.

Vehicle or AC charging

connector failure

Check for power system fault/failure warning

light or message on the instrument cluster.

If found, stop charging and contact a BYD

authorized dealer or service provider.

Power battery

temperature above or

below specification

Warm up or cool down the power battery.

The power battery has

been fully charged.

Charging automatically stops when the power

battery is fully charged.

Charging stops

halfway.

The charging cable is

not properly connected.

Ensure the charging connecting device is

properly connected.

AC supply is interrupted.

Charging will restart automatically a while

after AC supply returns to normal. If it doesn't,

reinsert the charging connector.

Power battery

temperature is too high.

A power battery overheating warning is

displayed on the instrument cluster. Charging

stops automatically and restarts after the

battery has cooled down.

Charging pile failure.

If the vehicle or charging pile displays a failure

message, contact a BYD authorized dealer or

service provider.

Содержание ATTO 3 2022










































































































































































































Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды

BYD ATTO 3 2022, Руководство пользователя

Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды