BYD ATTO 3 2022 Скачать руководство пользователя страница 19

Страница: 19 / 201

CAUTION!

•In order to prevent damage, do not let

any part of the seat belt get caught in

the door or back seat.

•Check all the vehicle's seat belts for

chafing, wearing out, loosening or any

other issues. If any problem is found,

contact a BYD authorized dealer or

service provider for confirmation and

handling. Until then, do not use the

corresponding seat.

•Do not remove, disassemble or modify

the seat belts without permission.

•After an accident, have the seat belts

checked at a BYD authorized dealer

or service provider. If the preloading

function is activated, the seat belt

must be replaced.

•In the event of a serious accident,

even if there is no apparent damage,

the seat belt should be replaced along

with the seat assembly. The airbag

system should also be thoroughly

inspected.

•Pregnant women should also fasten

their seat belt with the correct

method just as other passengers.

Particularly, be sure to position the

lap belt portion of the seat belt as low

across the hips as possible, to prevent

serious injury.

•The back seat belts' fastening method

is the same as the front's. For proper

protection, make sure the latch is

inserted in its corresponding buckle.

It is the driver's responsibility to

remind passengers to fasten seat

belts properly.

•In order to prevent damage, do not

insert any foreign object into the

buckle.

Unfastened Seat Belt Reminder

Function

If any vehicle occupant fails to fasten their

seat belt after the vehicle is started, a

visual and sound alarm will go off until the

corresponding seat belt has been properly

fastened.

• Unfastened seat belt indicator

• If any seat belt remains unfastened,

the unfastened seat belt indicator will

flash.

• Display of the unfastened seat belt

position

• The indicator displays the

corresponding position of the

unfastened seat belt.

• Unfastened Seat Belt Reminder for

Passengers

• If any seat belt is unfastened after the

vehicle is started ("OK" on cluster), the

indicator displays both detection and

position of the unfastened seat belt. If

the seat belt remains unfastened after

the vehicle starts moving, a warning

will sound to remind the occupants.

REMINDER

•If any fault is found, contact a BYD

authorized dealer or service provider

for confirmation and handling. Until

function is restored to normal, do not

use the corresponding seat.

•It is imperative that all vehicle

occupants have their seat belts

fastened when the vehicle is in

motion, otherwise they will be under

serious risk of injury or even casualty

in case of an accident.

Содержание ATTO 3 2022










































































































































































































Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды

BYD ATTO 3 2022, Руководство пользователя

Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды