BYD ATTO 3 2022 Скачать руководство пользователя страница 53

Страница: 53 / 201

• When anti-theft mode is activated, if no

door is opened within 30 seconds after

all doors have been unlocked with the

smart key, they will lock automatically.

• If the smart key is left inside the cabin or

trunk of the locked vehicle, and the door

or trunk is closed, the vehicle will unlock

automatically and the turning lights will

flash twice.

• If the vehicle is equipped with four-

door anti-pinch function and the lock/

unlock button is pressed for a long time,

locking/unlocking will not be repeated.

It is necessary to release this button and

press lock/unlock again. When the lock

button is pressed and held, the vehicle's

four windows will automatically rise.

REMINDER

•If the ignition switch is not on OFF,

the Lock or Unlock button cannot be

used to lock or unlock doors.

Opening Trunk with Smart Key

• Press the smart key trunk unlock button

twice to open the trunk. The turning

lights will flash twice.

REMINDER

•Don't forget to carry the smart key

when leaving the vehicle.

Smart Key Car Search

• If the vehicle is in anti-theft mode, it will

generate a long beep and the turning

lights will flash 15 times when the lock

button is pressed, in order to confirm

the vehicle's location when it cannot be

found.

• When the vehicle is in the car search

mode, press the Lock button again and

the vehicle enters the next car search

mode.

Raising/Lowering Windows with

Smart Key

• When the ignition switch is on OFF:

•

Press and hold the smart key lock

button to raise the four windows.

•

Press and hold the smart key unlock

button to lower the four windows.

WARNING

•

When using the remote control

function to raise windows, pay

attention to the safety of occupants in

the vehicle, and use this function only

after making sure the windows are

clear from pinching anyone.

REMINDER

•Users can turn this function on/off by

pressing and holding the smart key

lock/unlock button and open/close

windows through → Vehicle

Settings → Doors, Windows and

Locks Settings interface (depending

on actual vehicle configuration).

Locking/Unlocking with

Microswitch

Locking

• When the ignition switch is on OFF and

all doors are closed but not locked, press

the front door handle microswitch while

carrying the smart key to lock all doors.

The turning lights will flash once.

• If any door, hood, or trunk is not closed,

the microswitch can be used to lock the

closed doors. The turning lights will not

flash but the horn will beep once.

Содержание ATTO 3 2022










































































































































































































Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды

BYD ATTO 3 2022, Руководство пользователя

Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды