BYD ATTO 3 2022 Скачать руководство пользователя страница 105

Страница: 105 / 201

104

CAUTION

•If the EPB switch is pressed and

shutdown, EPB will not be pop up

automatically. This operation can be

used for towing or pushing the vehicle

in case of breakdown.

•During this process, the brake pedal

should not be released in advance,

especially when the vehicle is parked

on a slope, as there is a risk the

vehicle will move down.

•This feature is intended to improve

the vehicle's autonomous safety,

and over-reliance or frequent use is

not recommended. To ensure safety,

make sure that the vehicle is set to the

"P" gear position or the EPB switch

is pulled up before getting out of the

vehicle.

•In the first few seconds after starting

the vehicle, the EPB system is in

the process of power-on self-test,

during which it will not respond to all

functions.

Manual EPB Release

• When power status is on "OK" or the

vehicle is started and the gearshift

lever is not on "P", press and hold the

brake pedal and press the EPB switch

until the indicator on the cluster is off,

which indicates EPB has been released,

and there will be an "EPB Released"

message.

CAUTION

•The "P" gear is the vehicle's parking

gear, meaning that the vehicle is in

a stable parking status, while EPB is

the vehicle's main parking device. To

ensure parking safety, release EPB

with the EPB switch only when the

vehicle is not in "P" gear (parking

gear).

EPB Automatic Release Upon

Vehicle Start

• When the vehicle is powered on, the

brake pedal is pressed and held, and

the gear is shifted into "D" or "R", EPB is

automatically released. The indicator

foes off and the "EPB released" message

is displayed.

CAUTION

•The brake pedal must always be

pressed when shifting gears. Release

the pedal only after the intended gear

is displayed on the cluster.

When the vehicle is in parking state, start

the vehicle, press and hold the brake pedal,

and shift from "P" or "N" gear into "D", "R"

or other driving gears, and EPB will be

released automatically, with the indicator

going and the message "EPB Released".

WARNING

•

Whenever possible, refrain from using

for forced braking. Use the emergency

braking function only extreme cases,

for example, when the brake pedal

fails or is blocked.

•

This is because EPB cannot exceed

the physical limit of road adhesion.

If the emergency braking function

is used in curves, dangerous or

congested roads, or in bad weather

conditions, the vehicle may drift, skid

or deviate.

Содержание ATTO 3 2022










































































































































































































Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды

BYD ATTO 3 2022, Руководство пользователя

Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды