Broadway Limited Steam Locomotive Скачать руководство пользователя страница 42

Страница: 42 / 50

Special Operation and

Troubleshooting

For a full description, see the Troubleshooting section in the Quantum DCC

Reference Manual (

Version 3

)

at www.broadway-limited.com.

With some Command Stations, using the whistle button to activate the

Whistle, and, while this button is held down, activating the F6 Doppler Key,

will cause the Whistle to shut off instead of causing a Doppler shift effect.
We have experienced intermittent and independent whistle signal

interruption with some DCC command stations, causing unexpected

Doppler shifts. If this happens frequently, you may want to disable the

Whistle Triggered Doppler (CV 51.2).

Manual Volume Adjustment (Analog and DCC)

To adjust the volume by hand:

•

Locate the Manual Volume Control on the roof of your steam

locomotive tender as shown in the

Steam Model Specification

sheet

that was included with your instructions.

•

Use a small screwdriver to turn the volume clockwise to increase

volume or turn it counterclockwise to decrease the volume.

Note:

Volume can also be adjusted digitally using the programming

methods described in the programming sections of this manual.

Using the Quantum Reset Jumper to Return Your Engine to Factory

Default Values (Analog and DCC)

In case your engine’s sound and control system misbehaves and turning

the power off for 15 seconds does not return it to normal operation, you can

reset your locomotive to original factory values. The jumper is located as

shown in the

Steam Model Specification

sheet that was included with your

instructions.

•

Turn off the power.

•

Remove the jumper by pulling it up.

•

Reapply power, the Whistle will sound with a series of three hoots

after a few seconds.

Содержание Steam Locomotive



















































Результаты поиска

Содержание Steam Locomotive

Отзывы:

Похожие инструкции для Steam Locomotive

Бренды по названию

Популярные бренды

Broadway Limited Steam Locomotive, Руководство оператора

Результаты поиска

Содержание Steam Locomotive

Отзывы:

Похожие инструкции для Steam Locomotive

Бренды по названию

Популярные бренды