Broadway Limited Steam Locomotive Скачать руководство пользователя страница 28

Страница: 28 / 50

DCC Programming

Most command stations currently available will program Quantum equipped

locomotives in Service or Ops Mode. If your command station will not

program in Service Mode, check with the command station manufacturer –

some companies will give you a free upgrade. Also, see

Special Operation

and

Troubleshooting

page 36

Changing the System Volume Electronically in CV 51.0

You can change the volume either manually as described in the

Special

Operation and Troubleshooting

section or electronically using CV 51.0 in

DCC

. To change volume in Service or Ops Mode, do the following:

•

Set CV 49 to 0.

•

Enter the System Volume in CV 51.

The System Volume can be set

to any value between 0 (no sound) and 127 (100%). The default

System Volume is 127.

Note:

When you change the System Volume, you will immediately notice

the change in volume in Ops Mode.

Changing the Mute Volume Electronically in CV 51.1

To change the Mute Volume in Service or Ops Mode, do the following:

•

Set CV 49 to 1.

•

Enter the Mute Volume in CV 51.

The System Volume can be set to

any value between 0 (no sound) and 63 (100%). The default Mute

Volume is 63.

Note:

When you change the Mute Volume, and the locomotive is muted,

you will immediately notice the change in Mute Volume in Ops Mode.

Note:

The Mute Volume level will be the smaller of either the Mute Volume

setting or one half the current System Volume. In other words, the Mute

Volume will never be more than one half the System Volume.

Enable/Disable Whistle Triggered Doppler Shift (CV 51.2)

•

Set CV 49 to 2.

•

Set CV 51 to 0 to disable Whistle Triggered Doppler, set to

1 to

enable Whistle Triggered Doppler.

Содержание Steam Locomotive



















































Результаты поиска

Содержание Steam Locomotive

Отзывы:

Похожие инструкции для Steam Locomotive

Бренды по названию

Популярные бренды

Broadway Limited Steam Locomotive, Руководство оператора

Результаты поиска

Содержание Steam Locomotive

Отзывы:

Похожие инструкции для Steam Locomotive

Бренды по названию

Популярные бренды