Broadway Limited Steam Locomotive Скачать руководство пользователя страница 36

Страница: 36 / 50

Special Operation and

Troubleshooting

For a full description, see the Troubleshooting section in the Quantum DCC

Reference Manual (

Version 3

) at

http://www.broadway-limited.com/.

With some command stations, using the whistle button to activate the

Whistle, and, while this button is held down, activating the F6 Doppler Key,

will cause the Whistle to shut off instead of causing a Doppler shift effect.
We have experienced intermittent and independent whistle signal

interruption with some DCC command stations, causing unexpected

Doppler shifts. If this happens frequently, you may want to disable the

Whistle Triggered Doppler (CV 51.2).

Reed Switch Operation with Magnetic Wand (Analog and DCC)

•

The locomotive is equipped with a special reed switch located directly

under the plastic tender roof that can be activated by the Magnetic

Wand (enclosed) without having to disassemble the locomotive. The

reed switch can be used to change the volume of your sound system

or to reset the engine to factory defaults.

Manual Volume Adjustment (Analog and DCC)

•

Locate the reed relay area on the locomotive’s tender as shown in

the

Steam Model Specification

s sheet that was included with your

model.

•

Power up engine and leave in Neutral. Make sure Bell is not on.

•

Place the enclosed Magnetic Wand over this reed switch area on the

roof of the locomotive’s

tender perpendicular to the track and wait

as you hear the volume increase or decrease in incremental amounts

as the Whistle hoots about every second. Move the wand away and

again place it over the reed area to change the direction (louder or

softer) of the volume change. Remove the wand when you reach the

desired volume level.

Note:

Volume can also be adjusted digitally using the programming

methods described in the programming sections of this manual.

Resetting your Engine to Factory Default Values with Magnetic Wand

Содержание Steam Locomotive



















































Результаты поиска

Содержание Steam Locomotive

Отзывы:

Похожие инструкции для Steam Locomotive

Бренды по названию

Популярные бренды

Broadway Limited Steam Locomotive, Руководство оператора

Результаты поиска

Содержание Steam Locomotive

Отзывы:

Похожие инструкции для Steam Locomotive

Бренды по названию

Популярные бренды