Broadway Limited Steam Locomotive Скачать руководство пользователя страница 25

Страница: 25 / 50

Dynamic Brake function has been included to make the Quantum steam

engine consistent with other Quantum equipped locomotives in consists.

•

Pressing the F5 key will set the steam exhaust Sound-of-Power

to the lowest setting allowing the steam labored sounds to be

consistent

with other engines that do have Dynamic Brake sounds

in multiple unit consists.

•

Pressing the F5 key in Neutral will have no Dynamic Brake effect

unless the locomotive is in Disconnect (see above).

The Dynamic Brake function automatically turns off when entering or

leaving Neutral, or if the throttle is turned up or the speed of the locomotive

drops below 7 smph

. The Dynamic Brakes cannot be turned on in Forward

or Reverse unless the engine is traveling over 8 smph.

Note:

In contrast to Air Brakes (F7), Dynamic Brakes do not increase the

deceleration rate specified by CV 4 and CV 24.

Start Up (F6)

If your steam locomotive is in any stage of Shut Down, you can return your

locomotive to normal operation by double pressing the F6 key. Start Up will

be different for each stage of Shut Down, but all will start up with a Long Air

Let-off and will enter normal operation.

Start Up from Disconnect:

If you double press the F6 key in Disconnect,

the steam locomotive will produce a Long Air Let-off and the locomotive will

enter normal operation.

Start Up from Standby:

If you double press the F6 key in Standby, the

steam locomotive will produce a Long Air Let-off, the Dynamo will start up

and Directional Lighting will turn on (if previously on) and then the engine

will enter normal operation.

Start Up from Total Shut Down:

If you double press the F6 key in Total

Shut Down, the steam locomotive will produce a Long Air Let-off, the

Dynamo will rev up and the Directional Lighting will turn on (if previously

turned “on” and a Normal Engine or Lead Helper), followed by the Air

Pumps starting up, the steam Blower turning on and then the locomotive

will enter normal operation.

Note:

During any of the Start Up procedures, none of the function keys are

active. If the throttle is turned up from zero during any of the above Start Up

procedures, the Start Up procedure will abort and the engine will enter normal

operation.

Содержание Steam Locomotive



















































Результаты поиска

Содержание Steam Locomotive

Отзывы:

Похожие инструкции для Steam Locomotive

Бренды по названию

Популярные бренды

Broadway Limited Steam Locomotive, Руководство оператора

Результаты поиска

Содержание Steam Locomotive

Отзывы:

Похожие инструкции для Steam Locomotive

Бренды по названию

Популярные бренды