Broadway Limited Steam Locomotive Скачать руководство пользователя страница 16

Страница: 16 / 50

on, then off and then on as described above.

•

After the “Enter Programming” followed by “Option One - System

Volume” announcement of the first Program Option, flip the direction

switch and leave it there. You hear the announcement “Option 1, 2, 3

… etc.”. Stop when you hear “eight” by moving the direction switch

back. You will hear “V-Start”.

•

Use a

Slow

Quick

operation of the direction switch to enter this

option. You will hear “V-Start equals X” where “X” is the track voltage

value currently set to leave Neutral”.

•

Use a

Slow

Quick

operation of the direction switch to activate

this option. Hear the message “Set throttle to V-Start” and after three

seconds the voltage will be announced

. If you move the throttle, the

new track voltage value is announced a few seconds later.

•

Once throttle is set, use a

Slow

Quick

operation of the direction

switch to start the procedure. The engine will move

at a slow speed

and the Bell will ring continually for about 25 seconds, indicating the

correct value is being calculated. If the locomotive does not move

during the procedure, return to the beginning of this option

or start

over and chose a slightly higher throttle setting.

•

At the end of the process, the engine will stop moving and the

Whistle will hoot, signifying the end of the operation and you will hear

the message “V-Start = X” where “X” is the new setting.

•

To leave Programming, turn the throttle off, and then power up for

normal engine operation.

•

Or continue to V-Max by moving the direction switch and waiting for

the next Programming Option to be announced.

Example 3: Setting V-Max (Program Option # 9)

V-Max is set in the same manner as V-Start except after entering this

Program Option, you will hear “Set throttle to V-Max” which is the position

where you want the full track voltage to be applied to the motor (usually

about 80% of full throttle)

. Then do a

Quick

Slow

operation to set V-

Max.

Note:

During the V-Max setting, the engine will not move as it does under

V-Start.

Note:

When double heading your Quantum equipped locomotives

, make

sure that both locomotives have similar speed/throttle characteristics by

Содержание Steam Locomotive



















































Результаты поиска

Содержание Steam Locomotive

Отзывы:

Похожие инструкции для Steam Locomotive

Бренды по названию

Популярные бренды

Broadway Limited Steam Locomotive, Руководство оператора

Результаты поиска

Содержание Steam Locomotive

Отзывы:

Похожие инструкции для Steam Locomotive

Бренды по названию

Популярные бренды