Broadway Limited Steam Locomotive Скачать руководство пользователя страница 40

Страница: 40 / 50

Sounds & Features

Common to Analog

& DCC

Analog Features*

DCC Features*

Whistle or hoot

Bell with shut down and

turn on

effects

Steam Exhaust (chuff)

Articulated Chuff

(optional)

Automatic Blower Hiss

Doppler Shift

Brake or Flange Squeal

Neutral Sounds

Long Air Release

Short Air Release

Air Pump

Dual Air Pumps

(optional)

Sound of Power™

Neutral State (Idle)

Directional Lighting

Bright Headlight

Reverse Light

(optional)

Cab Lights (optional)

Manual Volume Control

with Magnetic Wand

(optional)

Reset to Factory Default

with Magnetic Wand

(optional)

System Volume Programming
Individual Sound Volume

Control

Regulated Throttle Control and

Locomotive Inertia

Helper Type: (Normal) Normal

loco, Lead Loco, Mid

Helper, End Helper. Pusher.

Direction: (Normal) Normal/

Reversed

Power Pack Programming

V-Max (12v)

V-Start (8.5v)

Shut Down & Start Up

with Magnetic Wand

(optional)

QARC™ Operation**

(with BLI QARC Controllers™)

Air Brakes

Flanges

Dynamic Brakes

Engine ID’s.

Consist ID’s.

Coupler Sounds

Extended Shut Down

Extended Start Up

Explicit Lighting Control

Controllable Flange

Squeal Load on/off

toggle

Blower on/off toggle

Verbal Engine Status

Grade Crossing Signal

Audio Mute

System Volume Control

and Additional Features

F0 or FL light control

F1-F12 Function Keys

14/28/126 speed steps (28)

Coupler Sounds

Air Brakes

Dynamic Brake Effect (for

consists)

Programming Modes

Supported:

Address Mode, Register Mode,

Service Mode, Direct Mode, Ops

Mode Long Form & Ops Mode

Short Form

NMRA



CV’s supported:

1 Primary Address

2 V-Start)

5 V-High)

8 QSI MFG’s ID Number (113)

3-4,7,17-25,29,33-46,66-95

QSI CV’s supported:

49 Primary Index

50 Secondary Index

51 Sound Control

51.0 System Volume

51.1 Mute Volume

51.2 Doppler (Enabled)

52 Individual Sound Volume

Control

53 Function Output Mapping

56 QSI Configuration

56.12 Chuff Interval Scale

Factor

56.128.

Reset

56.253

Version Build

Information

62 Auto CV Verbal Feedback

(enabled)

64 CV Inquiry Verbal Readout

*Settings in parentheses indicate factory default

**QARC

Technology allows commands to be sent to engines under Analog control

to operate different Quantum features. With QARC technology, you can operate

features that are otherwise available only in DCC plus features that are not yet

available in DCC. The QARC controllers are inexpensive accessories that employ

the QARC system. They can be added to your existing power pack to operate

additional features on your Quantum

equipped locomotive.

Содержание Steam Locomotive



















































Результаты поиска

Содержание Steam Locomotive

Отзывы:

Похожие инструкции для Steam Locomotive

Бренды по названию

Популярные бренды

Broadway Limited Steam Locomotive, Руководство оператора

Результаты поиска

Содержание Steam Locomotive

Отзывы:

Похожие инструкции для Steam Locomotive

Бренды по названию

Популярные бренды