Bowflex HVT Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 163

background image

3

SAFETY WARNING LABELS AND SERIAL NUMBER

FCC Compliance

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

The machine and power supply comply with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This machine and power supply have been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Serial Number

Product Specification

Power Inlet

WARNING!

- Injury or death is possible if

caution is not used while using this

machine.

- Keep children and pets away.

- Read and follow all warnings on

this machine.

- Refer to to the Owner’s Manual for

additional warnings and safety infor-

mation.

- The heart rate displayed is an

approximation and should be used

for reference only.

- Not intended for use by anyone

under 14 years of age.

- The maximum user weight for this

machine is 300 lbs (136 kg).

- This machine is for home use only.

- Consult a physician prior to using

any exercise equipment.

CAUTION / ATTENTION

NOTICE:

This document provides important safety instructions, adjustments, and general troubleshooting information for the maintenance of the Bowflex

®

HVT

™

machine.

If you need assistance, please call

Bowflex

Customer Service at 1-800-605-3369.

«
1
2
3
4
5
...
»

Содержание HVT




































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HVT

Бренд: ACS Страницы: 56

Бренд: KaVo Страницы: 13

Бренд: vc999 Страницы: 52

WJHD100 - DIGITAL DISC RECORDE

Бренд: Panasonic Страницы: 7

Бренд: Malmet Страницы: 14

Бренд: Zempire Страницы: 2

Бренд: Cambridge Audio Страницы: 2

Бренд: Quanser Страницы: 12

Бренд: Tascam Страницы: 78

MINISTUDIO CREATOR US-42

Бренд: Tascam Страницы: 11

Бренд: YASKAWA Страницы: 81

Бренд: YASKAWA Страницы: 52

Бренд: Lalizas Страницы: 12

BOBCAT 130 Series

Бренд: Balcrank Страницы: 12

Бренд: DC Med Страницы: 2

SnapTable PRO Hyper-Lite

Бренд: SWENSON SHEAR Страницы: 12

Бренд: Amadas Страницы: 111

Eclipse BPM-30E

Бренд: Groen Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды