background image

8015344.021518.E

8015343.021518.F

Service Manual

Table of Contents

Section 

Code 

 

Section 

 

     Page 

Number

 

 

Important Safety Instructions  

 

 

 

 

2

 

 

Safety Warning Labels and Serial Number   

 

 

3

 

 

Specifications  

 

 

 

 

 

4

 

 

Moving and Storing the Machine   

 

 

 

5

 

1   

Leveling 

the 

Machine 

     

5

 

1   

Connectivity 

      

6

 

1   

Maintenance 

      

7

 

 

Maintenance Parts Exploded View  

 

 

 

8

 

1   

Troubleshooting 

 

     

10

 

1   

Machine 

Settings 

Mode 

     

11

 

 

Replacement Procedure Skill Level 

 

 

 

12

 

 

Mechanical / Modification Procedures 

 

2   

Adjust 

Ropes 

      

13

 

 

Install Platform Decking Shim 

 

 

 

 

15

 

4   

Install 

Shaft 

Spacer 

     

19

 

5   

Reset 

the 

Console 

     

22

 

6   

Update 

the 

Firmware 

     

23

 

 

Part Replacement   

 

7   

Replace 

the 

Brake 

Assembly 

    

27

 

8   

Replace 

the 

Brake 

Disc 

     

32

 

 

Replace the Console Bezel Assembly 

 

 

 

37

 

10 

 

Replace the Console Cable Assembly 

 

 

 

40         

 

11 

 

Replace the Deep V Pulleys 

 

 

 

 

43

 

12 

 

Replace the Elastic Cord (Bungee) 

 

 

 

51

 

13   

Replace 

the 

Fan 

Assembly 

    

59

 

14 

 

Replace the Floating Pulley 

 

 

 

 

63

 

15   

Replace 

the 

Frame 

Assembly 

    

67

 

16 

 

Replace the Front Platform Frame  

 

 

 

77

 

17 

 

Replace the Load-Bearing Floating Pulley   

 

 

81

 

18 

 

Replace the Lower Chassis Cable  

 

 

 

86

 

19 

 

Replace the Lower Left Rope 

 

 

 

 

91

 

20 

 

Replace the Lower Right Rope   

 

 

 

99

 

21 

 

Replace the Low-Tension Floating Pulley   

 

 

107

 

22 

 

Replace the Middle Pulley Arm   

 

 

 

112

 

23 

 

Replace the Plain Bearing Pulley   

 

 

 

117

 

24 

 

Replace the Platform Decking 

 

 

 

 

121

 

25 

 

Replace the Platform Frame 

 

 

 

 

125

 

26   

Replace 

the 

Power 

Inlet 

     

132

 

27 

 

Replace the Servo Motor 

 

 

 

 

135

 

28   

Secure 

the 

Servo 

Motor 

     

141

 

29 

 

Replace the Speed Sensor Assembly 

 

 

 

147

 

30 

 

Replace an Upper Pulley Retainer  

 

 

 

153

 

31   

Replace 

an 

Upper 

Rope 

     

156 

Nautilus, Inc., www.NautilusInc.com - Customer Service: North America (800) 605-3369, [email protected] | outside U.S. www.nautilusinternational.com | Printed in China | © 2017 Nautilus, Inc. | ® indicates 

trademarks registered in the United States. These marks may be registered in other nations or otherwise protected by common law. Bowflex, the B logo, and HVT are trademarks owned by or licensed to Nautilus, 

Inc.

Bowflex

®

 HVT

 machine

Service Manual

Содержание HVT




































































































































































Отзывы: