Boss X-POT 6+ Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 32

background image

BOSS

TM

X-POT6+ Operation & Maintenance Manual

(V1.2 September 2017)

Page 22

dosInG & WAteR tReAtment

ChemICALs

To manually dose the system, it may only be carried when the system is shut down and
the BOSS™ X-POT6+ has been hydraulically isolated from the main system water pressure
and also electrically isolated from the main system power supply.

The X-POT6+ equipment must be taken out of service and guarded against un-intentional
re-starting until the Water Treatment Chemicals are dosed into the X-POT6+ Vessel (4).

Dosing of Water Treatment Chemicals can only be achieved when the main System Pumps
are operational, make sure they are working and the system is running.

BSS Industrial recommend the ‘X-PO’ Range of Water Treatment

Chemicals for use in Commercial Heating and Cooling Systems.

BOSS™ X-PO10

BOSS™ X-PO20

BOSS™ X-PO35

BOSS™ X-PO40

BOSS™ X-PO45

Commercial

Inhibitor

De-Scaling

Agent

Sanitiser and

Cleanser

(Non-Flush)

Heavy Duty

De-Sludger

New System

Cleaner

BOSS™ X-PO50

BOSS™ X-PO55

BOSS™ X-PO60

BOSS™ X-PO65

BOSS™ X-PO80

Monopropylene

Non Hazardous

Glycol

Anti-Freeze,

Ready Mixed

Monopropylene

Non Hazardous

Glycol

Anti-Freeze,
Concentrate

Monoethylene

Glycol

Anti-Freeze,

Ready Mixed

Monoethylene

Glycol

Anti-Freeze,
Concentrate

System

Biocide

Note:
The safety circuits and data transmissions (if applicable) made or broken while shutting
down and could trigger the BMS Alarms or lead to false failure information.

•

Operating instructions for relevant system heating or cooling units must be observed.

To make the hydraulic components safe, isolate the relevant sections and vents using

the relevant drain valves and relieve the pressure.

•

The equipment is to be worked on only when in a safe and cool condition.

•

Do not attempt to work on this equipment at elevated temperatures.

•

Use of eye/face/hand protectors is required as the eyes or face could be injured by
spraying fluids if the isolating valves have not been closed properly.

«
...
20
21
22
23
24
...
»

Содержание X-POT 6+

































Отзывы:

Нет отзывов

Похожие инструкции для X-POT 6+

Бренд: NAD Страницы: 10

Бренд: QBC Diagnostics Страницы: 65

Бренд: Mandam Страницы: 9

Бренд: M-system Страницы: 2

Бренд: Rico Страницы: 34

Бренд: Landi Renzo Страницы: 16

Бренд: IBM Страницы: 163

Бренд: Xycom Страницы: 65

Бренд: Xtool Страницы: 8

Бренд: Yamaha Страницы: 48

FLEX-FOOT ASSURE

Бренд: Össur Страницы: 82

Бренд: Össur Страницы: 32

Digital Measuring System forUnloader & CTi CM...

Бренд: Össur Страницы: 6

DH Offloading Post-Op StyleShoe

Бренд: Össur Страницы: 32

Бренд: Össur Страницы: 65

Бренд: Össur Страницы: 92

Бренд: Össur Страницы: 38

Exitronix LEMD Series

Бренд: BARRON Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды