Boss X-POT 6+ Скачать руководство пользователя | Manualshive

Страница: 16 / 32

background image

BOSS

TM

X-POT6+ Operation & Maintenance Manual

(V1.2 September 2017)

Page 16

CommIssIonInG (continued)

2. Enable filtering

It is important to visually inspect the electrical connections, components and conduit
serving the BOSS™ X-POT6+ unit before commencement of the operation of the unit.

It is important to visually inspect the BOSS™ X-POT6+ unit hydronic connections before

commencement of the operation of the unit to confirm the following;

•

The integrity of all fittings and pipework connecting the heating / chilled system to
the BOSS™ X-POT6+ – Ensure there are no leaks.

•

The closure lid of the BOSS™ X-POT6+ is closed and sealed tight in accordance with
the ‘Bolt Tightening’ method in Section 5 (page 26) of this document.

•

All isolating valves ‘as supplied’ used to drain the BOSS™ X-POT6+ are closed with the
valve handles at 90° to the pipework they are connected to. Refer to page 10 for the
BOSS™ X-POT6+ Schematic, valve references 12, 16 & 19.

•

All isolating valves ‘as supplied’ which connect the BOSS™ X-POT6+ to the main
heating / chilled system should be in the ‘open’ position. Rotate the valve handles
to be in-line with the pipework it is connected to. Refer to page 10 for the BOSS™
X-POT6+ Schematic, valve references 1, 3, 8 & 11.

•

When the BOSS™ X-POT6+ has been filled with system water and pressurised, check
the hydronic integrity of all fittings and pipework within the BOSS™ X-POT6+ unit –
Ensure there are no leaks. To confirm the BOSS™ X-POT6+ has been filled, check the
2No Pressure Gauges (23 & 24) are operational.

•

Any system air will be drawn out through the Automatic Air Vent, item (18). This is a
normal procedure.

2.1. Circulation Pump

The Circulation Pump (item 10) installed onto this BOSS™ X-POT6+ is a WILO ‘Yanos Para
ST25/7.5 130’. The pump needs to be set at SPEED 3 for the BOSS™ X-POT6+ to operate

correctly.

2. Activation

The BOSS™ X-POT6+ can now be activated by turning the Isolator Switch from the ‘Off’
position to the ‘On’ position. The VEXO

®

iX-1 Controller will now scroll the following...

<

Filter Pump Run

>

«
...
14
15
16
17
18
...
»

Содержание X-POT 6+

































Отзывы:

Нет отзывов

Похожие инструкции для X-POT 6+

Бренд: Tanco Страницы: 72

Бренд: HABYS Страницы: 16

Бренд: Acterna Страницы: 72

ECL Comfort 210

Бренд: Danfoss Страницы: 28

Бренд: Tascam Страницы: 8

Бренд: Yamaha Страницы: 46

C-HB-A-LB2-SCCT Series

Бренд: C-LITE Страницы: 9

X-431 Torque HD

Бренд: Launch Страницы: 3

Бренд: Veit Brisay Страницы: 18

Бренд: AMVAC Страницы: 81

Бренд: Topcon Страницы: 76

Бренд: Leica Страницы: 36

Fast Track Solo

Бренд: Avid Technology Страницы: 24

Nebula Blizzard v3

Бренд: Lanta Страницы: 8

BreadSlicer 208

Бренд: Daub Страницы: 11

Бренд: JEOL Страницы: 4

Бренд: Milwaukee Страницы: 2

AccuTrak VPE-2000

Бренд: Superior Signal Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды