Bosch rexroth HS5E Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 104

Bosch rexroth HS5E Скачать руководство пользователя страница 94

94

/104

A4... with HS5E(V)(L) control system Series 1x and 30

| Troubleshooting

Bosch Rexroth AG, RE 92076-01-B/2021-04-22

14.3 Malfunction table

Table 27: Axial piston unit malfunction table

Malfunction

Possible cause

Remedy

Unusual noises

Insufficient air bleeding of the hydraulic system Fill the axial piston unit, suction line for the

hydraulic pump and the reservoir
Completely air bleed the axial piston unit and
hydraulic system
Check correct installation position

Insufficient suction conditions, e.g. insufficient
dimensioning of the suction line, viscosity of
the hydraulic fluid too high, suction height too
high, suction pressure too low, foreign particles
in the suction line, impermissible filter in the
suction line

Machine/system manufacturer: Check the
system, e.g. optimize inlet conditions, use
suitable hydraulic fluid
Fill the suction line with hydraulic fluid

Remove foreign particles from the suction line

Drive speed too high

Machine/system manufacturer: Reduce drive
speed

Wrong direction of rotation

Machine/system manufacturer: Check correct
direction of rotation, see chapter 7.4.1
"Preparation" on page 45

Improper mounting of the axial piston unit

Check the mounting of the axial piston
unit according to the specifications of the
machine/system manufacturer – observe
tightening torques

Improper mounting of assembled parts,
hydraulic lines or improper installation of the
coupling

Fasten assembled parts according to the
parameters provided by the coupling fitting
manufacturer

Valve and controller vibrate

Optimize the adjustment of the controller
of the axial piston unit and the pressure
limitation in the hydraulic system

Mechanical damage to the axial piston unit
(e.g. bearing damage)

Replace axial piston unit

Contact Bosch Rexroth Service

Increased, unusual vibration

Bearings worn

Contact Bosch Rexroth Service

«
...
92
93
94
95
96
...
»

Содержание rexroth HS5E









































































































Отзывы:

Нет отзывов