Bosch rexroth HS5E Скачать руководство пользователя страница 85

Страница: 85 / 104

RE 92076-01-B/2021-04-22, Bosch Rexroth AG

Maintenance and repair |

A4... with HS5E(V)(L) control system Series 1x and 30 85

/104

10 Maintenance and repair

NOTICE

Overdue inspection and maintenance work!

Property damage!

▶ Perform the specified inspection and maintenance work at the intervals

described in this manual.

10.1 Cleaning and care

NOTICE

Damage to seals and electrical system due to mechanical effects!

The jet of a high-pressure cleaner may damage the seals and electrical system of
the axial piston unit!

▶ Do not point the high-pressure cleaner at sensitive components, e.g. shaft seal

ring, electrical connections, and electrical components.

For cleaning and care of the axial piston unit, observe the following:

▶ Check whether all seals and plug-in connections are securely seated to ensure no

moisture can penetrate into the axial piston unit during cleaning.

▶ Use only water and, if necessary, a mild cleaning agent to clean the axial piston

unit. Never use solvents or aggressive cleaning agents.

▶ Remove major external contamination and keep clean sensitive and important

components, such as solenoids, valves, indicators and sensors.

Содержание rexroth HS5E









































































































Результаты поиска

Содержание rexroth HS5E

Отзывы:

Bosch rexroth HS5E, Инструкция по эксплуатации, Страница: 85 / 104

Результаты поиска

Содержание rexroth HS5E

Отзывы: