manualshive.com logo in svg

Bosch rexroth HS5E, Инструкция по эксплуатации, Страница: 21 / 104

Поделиться
Скачать
Bosch rexroth HS5E Скачать руководство пользователя страница 21

RE 92076-01-B/2021-04-22, Bosch Rexroth AG

 

Scope of delivery |

 A4... with HS5E(V)(L) control system  21

/104

4  Scope of delivery

3

5

2

7

4

1

6

Fig. 1: Example: Axial piston unit A4VSO with HS5EP control system, clockwise rotation with 
through drive

Included in the scope of delivery:

 

• Axial piston unit HS5E(V)(L)(P) control system according to order confirmation

The following parts come assembled on the unit:

 

• Transport protection of the drive shaft with keyed shafts (

1

)

 

• Protective covers (

2

)

 

• Protective plug/threaded plug (

3

)

 

• For version with optional through drive (U99) plugged with pressure-tight cover (

4

)

 

• HS5E pilot control valve (

5

)

 

• Swivel angle sensor (

6

)

 

• Pressure transducer (1x with open circuit, 2 pieces with closed circuit) including 

cable (

7

) (only with HS5E(V)(L)

P

)

Содержание rexroth HS5E









































































































Отзывы:

Нет отзывов