Bosch rexroth HS5E Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 104

Bosch rexroth HS5E Скачать руководство пользователя страница 100

100

/104

A4... with HS5E(V)(L) control system Series 1x and 30

| Troubleshooting

Bosch Rexroth AG, RE 92076-01-B/2021-04-22

Table 28: Malfunction table of HS5E control systems

Malfunction

Possible cause

Remedy

Drive motor shuts down due to
overloading

Excessive power consumption of the pump

Reduce torque limit
Reduce swivel angle command value
Check actual pressure value acquisition

Overcurrent protection of motor does not work
properly

Check setting and function

Piston is stuck in the HS5E pilot control valve
Diagnosis: Compare actual value and valve
command value in IndraWorks

Replace the HS5E pilot control valve,
see chapter 10.5.1 on page 87

Actual swivel angle value acquisition maladjusted
or not functioning properly

Swivel angle measurement check

Valve electronics defective

Replace the HS5E pilot control valve,
see chapter 10.5.1 on page 87

Hydraulic fluid temperature too
high

Too high inlet temperature at control system

Inspect system, e.g. malfunction in the
cooler, insufficient hydraulic fluid in the
reservoir

DB in preload valve opens
Diagnosis: Pipe to the reservoir heats up

Pressure must be lower than the cracking
pressure of the preload valve. Keep
overshoots and pressure pulsation to
a minimum

Malfunction of the pressure control valves
(e.g. high-pressure relief valve, pressure cut-off,
pressure controller)

Contact Rexroth Service

Control system worn out

Replace the control system, contact Rexroth
Service

Setting of swivel angle sensor
causes problems

For more information on this topic, refer to
chapter 8.1.5.4

The connection to IndraWorks
has failed; the row on the
display is red.

Input error

Use 192.168.0.1 as the correct IP address

14.3.1 Swivel angle measurement check

The settings for swivel angle measurement are made at the factory. After you
have replaced the swivel angle sensor, you must carry out calibration; see chapter
8.1.8 "Calibrating the HS5E(V)(L) control system" on page 80. Bosch Rexroth
recommend repeating calibration or checking it at certain intervals.

«
...
98
99
100
101
102
...
»

Содержание rexroth HS5E









































































































Отзывы:

Нет отзывов