Bosch rexroth HS5E Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 104

Bosch rexroth HS5E Скачать руководство пользователя страница 59

RE 92076-01-B/2021-04-22, Bosch Rexroth AG

Installation |

A4... with HS5E(V)(L) control system Series 1x and 30 59

/104

7.6.5 X7E1 and X7E2: Plug-in connector assignment for Ethernet interface

(coding D), M12, 4-pin, socket

Table 17: Pin assignment of X7E1 and X7E2:

Pin

Assignment

1

TxD +

2

RxD +

3

TxD -

4

RxD -

5

not assigned

Use a shielded bus cable as the data cable. When doing this, the shield should be
connected to the connector housing.

7.6.6 LED status indicators

LEDs 1, 2, 5, and 6 refer to interfaces "X7E1" and "X7E2"
- Link: Cable is plugged in, connection has been established (lit up permanently)
- Activity: Data has been sent/received (flashing)
Module status LEDs 3 and 4 refer to the electronics module
For a detailed description of the diagnosis LEDs, refer to the functional
description of the Rexroth HydraulicDrive.

Table 18: Indicators of status LED

Module status
LED (LED 4)

Indicator status

Network status
LED

Indicator status

Off

no voltage supply

Off

no voltage supply

Green/red flashing

Self-test

Green

Operation

Green flashing

Drive ready for

operation

Green

in control

Red flashing

Warning

Red

Fault

LED

Interface

Sercos

EtherNET/IP

EtherCAT

PROFINET

1

X7E1

Activity

Activity

not used

Activity

2

Link

Link

Link/Activity

Link

3

Electronics-

module

S

Network status

Network status Network status

4

Module status

Module status

Module status

Module status

5

X7E2

Activity

Activity

not used

Activity

6

Link

Link

Link/Activity

Link

«
...
57
58
59
60
61
...
»

Содержание rexroth HS5E









































































































Отзывы:

Нет отзывов