Bosch rexroth HS5E Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 104

Bosch rexroth HS5E Скачать руководство пользователя страница 91

RE 92076-01-B/2021-04-22, Bosch Rexroth AG

Disposal |

A4... with HS5E(V)(L) control system Series 1x and 30 91

/104

12 Disposal

Careless disposal of the axial piston unit, the hydraulic fluid and the packaging
material can result in environmental pollution.
Observe the following when disposing of the axial piston unit:

1.

Completely drain the axial piston unit.

2.

Dispose of the axial piston unit and packaging material in accordance with the
regulations in your country.

3.

Dispose of the hydraulic fluid in accordance with the regulations of your
country. Also observe the applicable safety data sheet for the hydraulic fluid.

4.

Disassemble the axial piston unit into its constituent parts for proper recycling.

5.

For example, separate the parts into:

– Castings

– Steel

– Aluminum

– Non-ferrous metal

– Electronic waste

– Plastic

– Seals

13 Extension and conversion

Do not modify the axial piston unit and/or its assembled parts. Unauthorized
conversions may cause malfunctions of the control and adjustment system or to
failure of the axial piston unit.
This also includes changing the settings, the wiring or the software.
Changes to settings on the customer side should only be made using the product-
specific setting instructions.

The warranty from Bosch Rexroth only applies to the configuration as delivered.
Any modification, extension or software customization voids the warranty.

Setting screws are protected against unauthorized adjustment by tamper-proof
caps. Removal of the tamper-proof cap will void the warranty. If you need to
change the settings, please contact your local contact person; you can find their
contact information at

www.boschrexroth.com/addresses

.

«
...
89
90
91
92
93
...
»

Содержание rexroth HS5E









































































































Отзывы:

Нет отзывов