Bomag BW 100 AC-4 Скачать руководство пользователя | Manualshive

Страница: 51 / 126

background image

Operation

BOMAG

51

BW 100/120/125 AD-4/AC-4

5.7

Driving the machine

Danger

!

Danger of accident!

Wet and loose soils considerably reduce the
ground adhesion of the machine on inclina-
tions and slopes.

Soil conditions and weather influences impair
the climbing ability of the machine.

Do not drive up and down inclinations which
exceed the maximum gradability of the ma-
chine (see chapter "technical data").

Driving across slopes should therefore be
strictly avoided, because of the high risk of tip-
ping over and the related risk of severe or even
fatal accidents.

You should therefore always drive straight up
or down a slope.

For rollers with a drum width of 1 m or less
there is a considerable risk of tipping over near
edges (e.g. curbstones, embankments, trench-
es, potholes) when driving over these edges.

Do not drive without wearing your seat belt.

Always give way to loaded transport vehicles!

Before starting to drive make sure that the
drive range is absolutely safe.

Drive and operate the machine only from the
driver’s seat.

Fig. 62

l

Set the throttle lever (Fig. 62) to full load posi-
tion "Max I" or "MAX II".

Caution

!

During operation the throttle lever always re-
mains locked in one of the full load positions.
Control the travel speed with the travel lever.

Fig. 63

Caution

!

Do not operate jerkily!

l

Disengage the travel lever (Fig. 63) out of
braking position and move it slowly to the de-
sired travel direction.

Position "I"

= max. forward travel without vi-

bration

Position "II"

= max. backward travel without

vibration

Position "III"

= Max. forward/backward travel

with vibration

Fig. 64

The parking brake warning light (g) (Fig. 64) in the
instrument cluster goes out.

«
...
49
50
51
52
53
...
»

Содержание BW 100 AC-4































































































































Отзывы:

Нет отзывов

Похожие инструкции для BW 100 AC-4

Бренд: Modulate Страницы: 2

Бренд: Jaga Страницы: 32

Бренд: LANGER EMV-Technik Страницы: 25

Electric Clamshell CSE12-208VCD

Бренд: Lang Страницы: 16

Бренд: Velleman Страницы: 16

Бренд: Velleman Страницы: 11

Бренд: M-system Страницы: 4

Бренд: Costan Страницы: 154

Бренд: Elenco Electronics Страницы: 12

Бренд: GRAVITY Страницы: 2

Бренд: HYDRA-RIB Страницы: 25

Бренд: Osprey Medical Страницы: 49

Бренд: B&G Страницы: 2

SnapTable PRO Hyper-Lite

Бренд: SWENSON SHEAR Страницы: 12

Бренд: HydroHoist Страницы: 19

Бренд: Handicare Страницы: 26

Бренд: Pilz Страницы: 12

ikon profile ww

Бренд: ADJ Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды