Bomag BW 100 AC-4 Скачать руководство пользователя | Manualshive

Страница: 106 / 126

background image

Every 2000 operating hours

BOMAG

106

BW 100/120/125 AD-4/AC-4

Fig. 169

l

Fill in new hydraulic oil (Fig. 169).

l

Perform a test run and check the system for
leaks.

Fig. 170

l

Check the hydraulic oil level on the dipstick
(Fig. 170).

Note

i

The breather filter for the hydraulic oil tank is inte-
grated in the filler cap. You should therefore re-
place the complete filler cap.

l

Close the tank with a new cover.

6.30 Changing the hydraulic oil

filter

Danger

!

Danger of scalding!

Danger of scalding by hot oil when unscrewing
the oil filter.

Caution

!

If the filter has to be changed together with the
hydraulic oil, the filter must only be changed
after the oil change and after the test run.

Do not use the oil in the filter bowl again.

Visible dirt may be an early sign for the failure
of system components and indicate the possi-
ble failure of components. In this case deter-
mine the cause and replace or repair the
defective components, if necessary. Negli-
gence may cause destruction to the entire hy-
draulic system.

Do not clean or reuse the filter element.

Apart from the normal oil change intervals, the
filter element must also be changed after major
repairs in the hydraulic system.

Environment

Catch running out oil, dispose of oil and filter
element environmentally.

Fig. 171

l

Remove filter bowl (4) (Fig. 171) with filter ele-
ment (3).

«
...
104
105
106
107
108
...
»

Содержание BW 100 AC-4































































































































Отзывы:

Нет отзывов

Похожие инструкции для BW 100 AC-4

Бренд: GE Страницы: 14

Бренд: GE Страницы: 11

Бренд: GE Страницы: 20

Druck ADTS 2 Series

Бренд: GE Страницы: 18

Бренд: Yamaha Страницы: 78

Бренд: Fast Страницы: 42

Бренд: DARAY Страницы: 28

Бренд: OMCA Страницы: 36

Бренд: Salford Страницы: 64

Бренд: idiag Страницы: 10

Бренд: Bandit Страницы: 136

Versaflo S Series

Бренд: 3M Страницы: 11

DBI Sala EXOFIT

Бренд: 3M Страницы: 32

Бренд: 3M Страницы: 8

Бренд: Accurate Bio-Medical Technology Страницы: 35

Бренд: Raven Страницы: 17

Бренд: Campbell Страницы: 12

Crouse-hinds series

Бренд: Eaton Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды