Bomag BW 100 AC-4 Скачать руководство пользователя

Страница: 47 / 126

Operation

BOMAG

BW 100/120/125 AD-4/AC-4

5.3

Electronic immobilizer

Before starting the engine the anti-theft protection*
must be disarmed by entering a code.

Fig. 51

Note

With the electronic immobilizer armed, the light
emitting diode (a) (Fig. 51) flashes slowly.

Slowly enter the six-digit user code.

Note

When entering the code, the light emitting diode
(6) lights up with every digit.

Press the diamond button.

The electronic immobilizer is now disarmed
and the engine can be started within the next
15 minutes.

5.4

Adjusting the operator's
seat

Danger

Danger of accident!

Do not adjust the seat while driving.

Fig. 52

To adjust the seat in longitudinal direction
push the lever 1 (Fig. 52) outwards.

Pull the lever (2) up and adjust the backrest.

Operate the lever (3) to adjust the weight of the
operator.

Note

In its setting the lever (3) is locked in upwards di-
rection. This lock can be released by pressing the
lever down against the end stop. Then adjust the
operator's weight by sliding the lever downwards.

Optional equipment

920390

Содержание BW 100 AC-4






























































































































Результаты поиска

Содержание BW 100 AC-4

Отзывы:

Похожие инструкции для BW 100 AC-4

Бренды по названию

Популярные бренды

Bomag BW 100 AC-4, Руководство по эксплуатации

Результаты поиска

Содержание BW 100 AC-4

Отзывы:

Похожие инструкции для BW 100 AC-4

Бренды по названию

Популярные бренды