Bomag BW 100 AC-4 Скачать руководство пользователя

Страница: 60 / 126

Operation

BOMAG

BW 100/120/125 AD-4/AC-4

5.15 Mounting/removing the chip

spreader

Danger

Danger of accident!

When mounting or removing the chip spreader
do not step between the chip spreader and the
machine while the engine is running.

Park the machine on a level and solid base to
mount or remove the chip spreader and shut
down the engine.

Mount and remove the chip spreader when it is
empty.

Mounting the chip spreader

Fig. 88

Lift the chip spreader by the lifting points (Fig.
88) and hook it carefully into the fixing points
on the machine.

Fig. 89

Insert the bolt (Fig. 89) and secure it with the
cotter pin.

Fig. 90

Connect the chip spreader hydraulically and
electrically with the machine (Fig. 90).

Disassembling the chip spreader

Empty the chip spreader, see section "Filling/
emptying the chip spreader".

Danger

Danger of accident!

Always stand the chip spreader on level and
firm ground.

Optional equipment

Содержание BW 100 AC-4






























































































































Результаты поиска

Содержание BW 100 AC-4

Отзывы:

Похожие инструкции для BW 100 AC-4

Бренды по названию

Популярные бренды

Bomag BW 100 AC-4, Руководство по эксплуатации

Результаты поиска

Содержание BW 100 AC-4

Отзывы:

Похожие инструкции для BW 100 AC-4

Бренды по названию

Популярные бренды