Bomag BW 100 AC-4 Скачать руководство пользователя

Страница: 114 / 126

As required

BOMAG

114

BW 100/120/125 AD-4/AC-4

Fig. 180

Take out the drain hose (Fig. 180).

Open the drain tap, let all water run out and
close the drain tap again.

Fig. 181

Unscrew the water hose at the water filter (Fig.
181).

Unscrew the water filter from the water tank.

Unscrew the filter element from the cover,
clean it and screw it back onto the cover.

Flush the water tank out with a strong water
jet.

Let all water with dirt run out.

Screw the cover with the filter element back
on.

Unscrew the plastic caps from the end of the
sprinkler tube.

Fill the water tank with clean water.

Activate the sprinkler system for a short while
so that all lines are flushed out.

Screw the olastic caps back on again.

Check the function of the sprinkler tubes, if
necessary clean or replace the nozzles.

Environment

Catch and dispose of old emulsion environ-
mentally.

Empty the emulsion tank

Fig. 182

Loosen the fitting, take the emulsion filter (Fig.
182) out and clean it.

Flush the emulsion tank thoroughly.

Reinsert the emulsion filter and tighten the fit-
ting.

Fig. 183

Fill the emulsion tank (Fig. 183).

Check the function of the sprinkler tubes, if
necessary clean or replace the nozzles.

AC-machines

Содержание BW 100 AC-4






























































































































Результаты поиска

Содержание BW 100 AC-4

Отзывы:

Похожие инструкции для BW 100 AC-4

Бренды по названию

Популярные бренды

Bomag BW 100 AC-4, Руководство по эксплуатации

Результаты поиска

Содержание BW 100 AC-4

Отзывы:

Похожие инструкции для BW 100 AC-4

Бренды по названию

Популярные бренды