Bomag BW 100 AC-4 Скачать руководство пользователя

Страница: 56 / 126

Operation

BOMAG

BW 100/120/125 AD-4/AC-4

Vibration in automatic mode

Note

In automatic mode the vibration is switched on
when exceeding a travel speed of 1.3 km/h.

Vibration is switched off at a speed below 1.3 km/
h.

Fig. 76

Turn the rotary switch for vibration in manual
or automatic mode (Fig. 76) clockwise to the
symbol "AUTOMATIC".

Switching the vibration on

Fig. 77

Set the throttle lever (Fig. 77) to position "Max
I" or "MAX II".

Fig. 78

Pull the travel lever (Fig. 78) out of zero posi-
tion (braking position) and shift it slowly to the
desired travel direction forward or backwards
("III")

Note

The vibration comes on at a low travel speed.

When shifting the travel lever through position "III"
to position "I" or "II", the vibration will be automati-
cally switched off.

Switching the vibration off

Shift the travel lever slowly to position 0.

The machine is decelerated and the vibration will
automatically switch off at a low travel speed.

Содержание BW 100 AC-4






























































































































Результаты поиска

Содержание BW 100 AC-4

Отзывы:

Похожие инструкции для BW 100 AC-4

Бренды по названию

Популярные бренды

Bomag BW 100 AC-4, Руководство по эксплуатации

Результаты поиска

Содержание BW 100 AC-4

Отзывы:

Похожие инструкции для BW 100 AC-4

Бренды по названию

Популярные бренды