BIRD 7001A900-2 Скачать руководство пользователя страница 79

Страница: 79 / 92

Maintenance

Figure 69 Firmware Installation Reboot

9. Refer to the LEDS on the front panel of the BDS.

Once the unit has finished rebooting the three status LEDs are glowing green.

Note:

wait 20 seconds after the three status LED’s are green before continuing.

10. Click

Confirm Update

button on the webpage, see

Figure 70

Figure 70 Confirm Update

11. Wait for the “Update confirmed successfully. Please reboot the BDS fr the update to take effect” message

before continuing. See

Figure 71

12. Click

Reboot

button on the webpage to reboot the BDS receiver a second time.

Figure 71 Final Reboot

13. Wait for the three LEDs on the front of the BDS return to green.
14. The receiver may now be used for RF Measurement.

Содержание 7001A900-2





























































































Результаты поиска

Содержание 7001A900-2

Отзывы:

Похожие инструкции для 7001A900-2

Бренды по названию

Популярные бренды

BIRD 7001A900-2, Руководство по эксплуатации

Результаты поиска

Содержание 7001A900-2

Отзывы:

Похожие инструкции для 7001A900-2

Бренды по названию

Популярные бренды