BIRD 7001A900-2 Скачать руководство пользователя страница 64

Страница: 64 / 92

Bird Diagnostic System

Note:

Displays “Yes” if automatic gain control is used or “No” if manual gain control is used.



Cal –

Measurement calibration indicator.

Note:

Displays “Yes” if the sweep data has been calibrated or “No” if it has not been calibrated.

Note:

Check the probe connection to the receiver if the BDS GUI is indicating that the measurements

are not being calibrated.



Arc –

Arc (transient) detected during the displayed measurement cycle.

Note:

This will display “No” if no transient event has been detected or “Yes” with a red background if a

transient has been detected during the measurement cycle.



Peak –

The peak number. Peaks are listed in ascending order (highest to lowest).



F (Hz) –

The frequency of the peak in Hz.

Selected amplitude. One of the following:



Vrms (Volts) –

RMS voltage.



Irms (Amps) –

RMS current.



Z (Ohms) –

Impedance in Ohms.



P (Watts) –

Power in Watts.



P (dBm) –

Power in dBm.

Содержание 7001A900-2





























































































Результаты поиска

Содержание 7001A900-2

Отзывы:

Похожие инструкции для 7001A900-2

Бренды по названию

Популярные бренды

BIRD 7001A900-2, Руководство по эксплуатации

Результаты поиска

Содержание 7001A900-2

Отзывы:

Похожие инструкции для 7001A900-2

Бренды по названию

Популярные бренды