Biddle CA M-150-W-F Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 60

Biddle CA M-150-W-F Скачать руководство пользователя страница 44

M

AINTENANCE

C

OMFORT

A

IR

C

URTAIN

44

Long-life filter in free-hanging models

1. Remove the inlet grate from the unit:

-

Lift the grate at the bottom and unhook it.

2. Loosen the screws

1

.

3. Remove the filter module

2

from the inlet grate.

4. Remove the filter from the filter module:

-

Loosen the screws

3

.

-

Remove the strip

4

.

-

Do the same on the other side of the module.

-

Take out the filter material

5

.

5. Clean or replace the filter.

6. Mount all components in reverse order to the dis-

mounting.

7. Reset the filter service life using function no. 2 at the

manager’s level (if tracking is enabled, see section

5.1.2

).

Long-life filter in recessed and cassette models

1. Take the inlet grille out of its frame:

-

Push the two pins

1

in the grille towards one

another – the grille will tilt down.

-

Push the two pins (at

2

) towards one another and take

the grille out.

1

1

2

3

3

3

4

5

1

1

2

2

«
...
42
43
44
45
46
...
»

Содержание CA M-150-W-F





























































Отзывы:

Нет отзывов