Biddle CA M-150-W-F Скачать руководство пользователя страница 37

Страница: 37 / 60

SER

’

AND

NSTALLER

’

ANUAL

ETTINGS

Version: 4.0 (23-08-2007)

4.4

Room temperature control

Working

The room temperature control allows you to prevent the air

curtain from overheating the room.

If the temperature in the room exceeds a certain value (the

set

point

), the discharge air temperature will be reduced to the

half temperature

You set the set point using function no. 5 at the manager’s

level (see section

4.2.3

The half temperature is the average of the set point and the

discharge air temperature, as pre-set by the user (see section

3.2 ’Selecting the air curtain strength’

Options

Function no. 51 at the installer’s level (see section

4.3.3

) allows

you to let the room temperature control work based on

either the temperature of the air taken in or the ambient tem-

perature near the control panel.

Discharge air temperature reading in

the display

0 = display pre-set discharge air

temperature

1 = display actual discharge air temperature

(default value).

The

- symbol appears in the display if

the discharge air temperature differs

from the pre-set temperature.

Release delay of external-control

input

See section

4.5.2

Pre-settable between 0 and 99 minutes

(default value = 0 (no delay)

Reading last 5 fault messages

91 = oldest message

95 = latest message

Содержание CA M-150-W-F





























































Результаты поиска

Содержание CA M-150-W-F

Отзывы:

Biddle CA M-150-W-F, Руководство пользователя и инсталлятора, Страница: 37 / 60

Результаты поиска

Содержание CA M-150-W-F

Отзывы: