Biddle CA M-150-W-F Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 60

Biddle CA M-150-W-F Скачать руководство пользователя страница 18

I

NSTALLATION

C

OMFORT

A

IR

C

URTAIN

18

Performing connection

Warning:

w

Make sure that the power supply you are working

on is switched off.

1. Fit the isolation switch and connect it to the power supply.

2. Remove the inspection panel:

-

Remove the screws

1

.

-

Pull the panel a little forward and take it away.

Caution:

c

The whole panel will come loose when you pull it for-

ward: take care it does not fall down.

3. Fix the cable swivel

2

to the unit. With the CA H, the

position of the cable swivel differs from that shown

4. Lead the power supply cable through the cable swivel.

5. Connect the cable to the terminal

3

in the unit accord-

ing to the wiring diagram.

Note:

n

The design in your unit may differ from the illustration.

6. Put back and screw down the inspection panel.

7. Connect the power supply cable to the isolation switch.

Caution:

c

Do

not yet

switch the power supply on.

1

1

1

1

2

3

«
...
16
17
18
19
20
...
»

Содержание CA M-150-W-F





























































Отзывы:

Нет отзывов