manualshive.com logo in svg

Biddle CA M-150-W-F, Руководство пользователя и инсталлятора, Страница: 21 / 60

Поделиться
Скачать
Biddle CA M-150-W-F Скачать руководство пользователя страница 21

U

SER

’

S

 

AND

 I

NSTALLER

’

S

 M

ANUAL

I

NSTALLATION

Version: 4.0 (23-08-2007)

21

7. Couple the connector to the printed circuit board 

4

.

8. Connect the external-control cable (if used) to the termi-

nal on the printed circuit board 

5

.

9. Put the front onto the back plate.

2.7.4 Connecting control panel to unit

The controller sockets 

1

 and 

2

 are located in the connector 

plate on the upper side of the unit. The two sockets are iden-

tical. One of the two sockets has a dummy plug.

1. Connect the control cable to the free socket 

1

 or 

2

.

Note:

n

Do 

not

 remove the dummy plug from the other socket, as 

this may lead to faults.

Note:

n

Allow some 30 cm excess cable length: it will be needed to 

take the electronics out when servicing the unit.

Multiple units operated from one single control panel

1. For each unit to be linked, remove the dummy plug from 

socket 

1

 or

2

.

2. Interlink the units: connect the control cables to 

1

 and 

2

.

Note:

n

Do 

not

 remove the dummy plug from the last unit, as this 

may lead to faults.

1

2

3

4

Содержание CA M-150-W-F





























































Отзывы:

Нет отзывов